Bissell 35799 ProHeat 2X Revolution Pet Upright Carpet Cleaner Manual

Bissell 35799 ProHeat 2X Revolution Pet Upright Carpet Cleaner

Product Overview

1. Upper Handle
2. Spray Trigger
3. Cord Clip
4. Easy Fill / Formula Cap
5. Clean Water Tank
6. Carry Handle
7. Cleaning Mode Switch
8. Power Button
9. Dirty Water Tank
10. Float Stack
11. Recline Pedal
12. Belt Access Door
13. Nozzle
14. Foot

IMPORTANT SAFETY INSTRUCTIONS

• Connect to a properly grounded outlet only. See grounding instructions. Do not modify the three-prong grounded plug.
• Do not leave the appliance when it is plugged in. Unplug from the outlet when not in use and before servicing.
• Use indoors only.
• Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
• Do not use for any purpose other than described in this user guide. Use only the manufacturer’s recommended attachments.
• Do not use with a damaged cord or plug. If the appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorised service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
• Do not run the appliance over the cord. Keep the cord away from heated surfaces.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not handle the plug or the appliance with wet hands.
• Do not put any object into openings. Do not use with any openings blocked; keep openings free of dust, lint, hair, and anything that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts of the appliance and its accessories.
• Turn OFF all controls before plugging or unplugging the appliance.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
• Do not use the appliance in an enclosed space filled with vapors given off by oil-based paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
• Do not use it to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
• Do not use without filters in place.
• Use only BISSELL® cleaning formulas intended for use with this appliance to prevent internal component damage. See the “Cleaning Formulas” section of this guide.
• Do not immerse. Use only on surfaces that have been moistened by the cleaning process.
• Keep the appliance on a level surface.
• Do not carry the appliance while in use.
• Always install the float before any wet pick-up operation.
• Unplug before connecting TurboBrush® Tool.
• Plastic film can be dangerous. To avoid the danger of suffocation, keep away from children.
• Liquid must not be directed towards equipment containing electrical components.
• Use only the type and amount of liquids specified under the operations section of this guide.

What’s in the Box?

Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton’s top flap.

Assembly

1. Insert the handle at the top of the base until it clicks.
2. Align the carry handle with the slots on either side of the base until it clicks into place. Use a Phillips-head screwdriver to insert the screw (taped to the handle).
3. Align the clean water tank with the grooves and slide it into place.

Filling the Clean Water Tank

This machine is compatible with BISSELL® formulas made for upright carpet cleaners. Always use genuine BISSELL formulas in your machine. Other formulas may harm the machine.

1. Choose your formula.* Scan the QR code with your smartphone camera or visit BISSELL.com for formulas.
2. Lift the clean water tank to remove it from the machine. Unscrew the cap.
3. Use MAX/DEEP Clean or Express Clean lines for regular formula. Use easy fill lines for the ANTIBACTERIAL formula.
4. Fill the tank with warm tap water (140°F/60°C MAX) to the WATER line. Do not use boiling water. Do not heat water or the tank in the microwave. Add formula to FORMULA line. Optional: Add 2 oz of OXY Boost. OXY Boost is not compatible with the easy fill ANTIBACTERIAL formula.
5. Screw the cap back on and slide the tank into place.

Cleaning Carpets and Area Rugs

Visit support.BISSELL.com for helpful how-to carpet cleaning videos.

• Remove any solids and use a dry vacuum cleaner before using your deep cleaner.
• To prevent damage to Berber carpets, avoid repeated strokes in the same area. Before cleaning area rugs, check the manufacturer’s tag and test an inconspicuous spot for colourfastness. Don’t use on silk or delicate rugs.
• Stay off the carpet until dry.

1. Plug into a properly grounded outlet. Select cleaning mode using the chart below. Press the power button to turn the machine ON.
2. Press the recline pedal with your foot. Hold the spray trigger for 10 seconds to wet the brush roll.
3. Make passes based on your selected cleaning mode (see chart below). When finished, turn the machine OFF.

Cleaning Modes & Instructions

MAX or DEEP Clean Mode

Delivers a deep clean to your carpet. Suggested Pace: 8 inches per second

• Hold the spray trigger
• One pass forward
• One pass back
• Release the spray trigger
• One pass forward
• One pass back

MAX or DEEP Clean Mode with BISSELL® ANTIBACTERIAL Formula

Suggested Pace: 8 inches per second

1. Hold the spray trigger
2. One pass forward
3. One pass back
4. One pass forward
5. Release the spray trigger
6. One pass back

Express Clean Mode

Provides a lighter clean that dries in about 30 minutes. Suggested Pace: 12 inches per second

• Hold the spray trigger
• One pass forward
• One pass back
• Release the spray trigger
• One pass forward
• One pass back
• With the trigger released, make passes until little water comes through the nozzle.

Cleaning with Hose and Tools

Tools vary by model. Visit BISSELL.com to purchase additional tools.

1. Lift the accessory hose door toward the machine to open.
2. Insert the hose and snap it into place with the colored release clip facing away from the machine.
3. Attach the tool to the end of the hose.

Deep Stain Tool; 3″, 4″ and 6″ Tools; and Spraying Crevice Tool

1. Point the tool about 1 inch above the spot or stain and press the spray trigger. Deep Stain Tool: Set the tool directly on the surface and pull the trigger. Always keep the tool in contact with the carpet to avoid over-spraying.
2. Release the spray trigger and gently scrub the stain.
3. Suction the stain by placing the tool onto the surface and slowly moving backwards.

3-in-1 Stair Tool

• Twist the tool to the desired position. The downward-facing edge is the active cleaning mode.
• Use to clean stairs in three ways:
• Flat edge: stair tread
• Indented area: outer corner
• Pointed edge: inner corner
• Point the tool about 1 inch above the stain and press the spray trigger. Suction the stain by placing the tool onto the surface and slowly moving backwards.

Stain Trapper Tool

1. Point the tool about 1 inch above the spot or stain and press the spray trigger. Suction up the stain by placing the tool onto the surface and slowly moving backwards.
2. To empty the tool tank, rotate clockwise. Pour dirty liquid into the sink or toilet and rinse. Allow time to air dry.
3. Return the tank to the tool by lining up the grooves and twisting it into place.

2-in-1 Upholstery Tool

• Switch between dry and wet settings and turn the machine ON.

Dry Cleaning

Vacuum up debris from carpet or upholstery.

Wet Cleaning

1. Hold down the trigger to activate the spray.
2. Release the trigger and suction up the stain.

Emptying the Dirt Bin

1. Twist the dirt bin to open. Empty debris into a garbage bin.
2. Rinse the dirt bin. Let dry completely before reinstalling.

Emptying the Dirty Water Tank

For more helpful maintenance tips, check out support.BISSELL.com.

1. Press the tank handle and tilt the tank toward you. Grab the handle and tank with both hands and pull up and away to remove.
2. Empty the tank. Quick empty: Pull the rubber tab and tilt to pour. When closing, ensure the tab is sealed tight. Final clean and rinse: Unscrew the ring at the bottom of the tank. Remove and rinse the float stack. Reinstall the float stack by aligning arrows and locking them into place. Twist and lock the ring to keep water from leaking.
3. 3. Clean the red filter below the tank by wiping off any remaining dirt or debris.

After-Cleaning Care

For more helpful maintenance tips, check out support.BISSELL.com.

Rinsing the Machine

1. Rinse out the clean water tank to remove formula. Fill the tank with warm tap water. Twist the cap back on tightly.
2. Turn the machine ON and press the trigger for 15 seconds while making back and forth passes on a section of carpet. Release the trigger and extract the water. See above to clean the dirty water tank.

Cleaning the Nozzle

1. Turn the machine OFF. Pull the accessory hose door up to remove the nozzle.
2. Rinse the nozzle. Use the clean-out tool to unclog debris.
3. Align the nozzle from the bottom and rotate to snap into place.

Cleaning the Brush Rolls

1. Turn the machine OFF. Lay the machine on its side or back.
2. Use the comb to brush out debris or hair from brush rolls.

Replacing the Belts and Brush Rolls

Scan the QR code or visit the website.

1. Unplug the machine and remove both tanks. Remove nozzle and brush roll cover (see steps in “After-Cleaning Care”). Press the recline pedal and lay the machine on its back.
2. Use a flathead screwdriver to press into the slot at the back and then the front of the belt access door. Lift to remove. Use a Phillips-head screwdriver to remove the screw under the wheel, and slide it down to remove.
3. Lay the machine on its back. Use a Phillips-head screwdriver to remove the screw on the brush roll endcap.
4. If the gear belt is broken or if replacing brush rolls, remove the belt. Be careful, the washers at the end of the brush rolls do not fall off or get lost.
5. Align the brush rolls with the belt at the other end. To ensure alignment, hold the end of one brush roll and twist. Check that washers are in place. Reassemble the belt and endcap, securing with screws.
6. If the flat belt is broken, gently remove it. If it needs replacing for any reason, remove the gear belt before removing the flat belt. With the machine on its side, feed the new belt through the opening and wrap it around the red pulley.
7. Lay the machine on its back. Stretch the flat belt to wrap around the metal axle.
8. Slide the wheel back into the slot and secure it with a screw.
9. Snap the belt access door back into place.

Troubleshooting

For a comprehensive walkthrough of your product and support tips, visit support.BISSELL.com. Any other servicing should be performed by an authorised service representative.

Warranty

Limited 5-year warranty, may vary by state. Visit support.BISSELL.com or call 1-800-237-7691 for complete warranty information. Every Purchase Saves Pets™ BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help make pet messes, odours, and pet homelessness disappear. Visit BISSELLsavespets.com to learn more.

For More Manuals By Bissell, Visit ManualsLibraryy

Bissell 35799 ProHeat 2X Revolution Pet Upright Carpet Cleaner -FAQS