Aerian AAC2300 Local Air Conditioner Instructions Manual

Aerian AAC2300 Local Air Conditioner

PARTS

Front and side views

Rear view

Accessories

Control panel

Buttons:

• Adjusting temperature or time
• °C / °F Press Minus and Plus buttons simultaneously for about 3 seconds to switch between Fahrenheit and Celsius degree

Indicator lights

Remote control

• The functions work the same as the control panel of the appliance

Buttons:

• Replace the battery: Slide the battery holder out ot the remote using the notch at the top. Put a new CR2025 battery on the battery holder with “+”facing up. Slide the battery holder back into the remote until it locks.

INSTALLATION

This appliance is a portable air conditioner, which can be moved from room to room.

1. Extend the air exhaust hose by drawing out the two ends of the hose.
2. Screw the air exhaust hose into the exhaust connector
3. Screw the slide bar adapter into the end of the air exhaust hose.
4. Insert the air exhaust assembly into the air outlet located at the rear of the appliance
   • IMPORTANT:
   • The exhaust hose may be stretched to its maximum length (approximately 150 cm). However, formaximum efficiency the hose should be set to the shortest length possible. Avoid kinks or bends in the hose.

Installing exhaust hose to window slide bar

Note: The window kit is only designed to be installed with sliding windows. The window kit is not designed or to be used with casement style windows.

1. Measure your window kit according to the dimensions of your sliding window.
   • If the slide bar is larger than your required dimensions, it can be cut using a  saw or power tool of the sort.
2. Extend the slide bar length to match the width of the window (vertically or horizontally).
3. Open your window and place the adjustable slide bar to the opening of the window.
4. Lower/shut the window until it holds the slide bar in place tightly.
5. Attach the exhaust hose with the slide bar connector to the opening of the window slide bar.

OPERATION

Plug the appliance into the mains socket. A buzzer will beep.

Turning ON/OFF

• Press Power button to turn on the appliance. The power indicator light will illuminate
• To turn it off, press Power button again. The power indicator light will go out.

Mode selection

Repeatedly press Home button  to select the desired working mode: fan, dehumidification, cooling or automatic The indicator light of your selected mode will flash for about 5 seconds and then stop flashing, indicating that the selected mode is confirmed.
tauto+

• Auto mode:
  The temperature sensor in the appliance will sense the ambient temperature to go into cooling or fan mode.
• Dehumidification mode
• This mode enables to reduce the level of humidity in the air.
• The appliance will run at the low fan speed. The fan speed and temperature cannot be adjusted.

Setting the temperature

Repeatedly press – / + to set the temperature from 15°C to 31°C. The set temperature will flash on the display for about 5 seconds and then stop flashing, indicating that the set temperature is confirmed.
NOTE: You cannot set the temperature in fan and dehumidification modes.

Setting the fan speed

• Repeatedly press to select the fan speed. The speed indicator light will illuminate to indicate which speed setting is in use. is in use
• NOTE: You cannot set the fan speed in the dehumidification mode.

Setting the timer

You can set the timer for both delay start and delay stop.

1. Press the Timer button  .The indicator lighton/off will flash on the display.
2. While the indicator light is flashing, repeateldy press +/ _to change the time in 1 hour increments up to 24 hours.
3. The indicator light will flash for about 5 seconds and then stop flashing, indicating that the set time is confirmed.
   • When the appliance is OFF, the delay start timer will start.
   • When the appliance is ON, the delay stop timer will start.
4. When the set time has been reached, the appliance will turn on or off automatically.
   • To cancel the timer setting, press Timer button twice.

Sleep operation (Cooling mode only)

• The sleep function adjusts the set temperature of the appliance to the thermal needs of the body falling asleep.
• Press to operate the sleep mode. The sleep indicator light Moon button will illuminate.
• In the cooling mode only, the set temperature will increase by 1°C after about one hour. The temperature will then increase by another 1°C after an additional one hour. After about six hours, the appliance will stop running.
• To cancel the function, press The sleep indicator light will go out.

DRAINAGE

When the internal water tank is full the display will show “E4”. The water tank full indicator light will illuminate. To empty the water tank do the following:

1. Switch off the appliance and remove the plug from the mains socket.
2. Place a water tray (not supplied) on the floor underneath the drainage point.
3. Remove the rubber plug from the drain and let the water run out.
4. Replace the rubber plug, plug the appliance into the mains socket, and switch the appliance on.

CLEANING AND MAINTENANCE

• Switch off and unplug the appliance from the mains socket before cleaning. To maximise the efficiency of the appliance clean it regularly.
• Cleaning the housing
• Clean the housing with a slight damp cloth. Never use chemical or abrasive cleaning agents.
• Cleaning the filters
• Remove the filters and clean them regularly. Use a vacuum cleaner or tap the filters lightly to remove loose dust and dirt from them and then rinse thoroughly under running water. Dry thoroughly before attaching them back to the appliance.
• NOTE: Never use the air conditioner without the filters.

Storage

• Drain all water in the appliance before completely operating the appliance on fan mode for a few hours, to thoroughly dry the inside of the appliance.
• Clean the filters.
• Remove the battery from the remote control.
• Place the appliance in a dry place.

For more manuals by Aerian, visit ManualsLibraryy

Aerian AAC2300 Local Air Conditioner-FAQs