Stanley Fatmax PP1DCS 1000 Peak Amp Power Station User Manual

Stanley Fatmax PP1DCS 1000 Peak Amp Power Station

DIGITAL LCD SCREEN

SAFETY GUIDELINES / DEFINITIONS

• DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
• WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
• CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
• CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

RISK OF UNSAFE OPERATION
When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

IMPORTANT  SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating the power station. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

WARNING:

• This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
• This unit was designed for household use only.
• WARNING: RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS OR PROPERTY
• Avoid dangerous environments Don’t use appliances in damp or wet locations. Don’t use appliances in the rain.
• Keep children away All visitors should be kept at a distance from work area.
• Dress properly Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.
• Store idle appliance indoors When not in use, appliances should be stored indoors in dry, and high or locked-up place – out of reach of children.
• Don’t abuse cord Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.
• Disconnect appliances Disconnect the appliance from the power supply when not in use, before servicing, and when changing accessories.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are available having built in GFCI protection and may be used for this measure of safety.
• Use of accessories and attachments The use of any accessory or attachment not recommended for use with this appliance could be hazardous. Refer to the accessory section of this manual for further details.
• Stay alert Use common sense. Do not operate this equipment when you are tired or impaired.
• Check for damaged parts Any part that is damaged should be replaced by the manufacturer before further use. Do not use tool if switch does not turn it on and off. Contact the manufacturer at (877) 571-2391 for more information.
• Do not operate this appliance near flammable liquids or in gaseous or explosive atmospheres Motors in these tools normally spark, and the sparks might ignite fumes.
• Never submerge this unit in water do not expose it to rain, snow or use when wet.
• To reduce risk of electric shock, disconnect the unit from any power source before attempting maintenance or cleaning. Turning off controls without disconnecting will not reduce this risk.
• This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor.

SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT

IMPORTANT

• This unit is delivered in a partially charged state. Fully charge unit with a household extension cord for a full 40 hours or until the battery status icon shows 4 solid bars before using for the first time. You cannot overcharge the unit using the AC charging method.
• To recharge this unit, use only the built-in AC charger with an AC extension cord (not included)
• All functions should be turned off when the unit is charging or not in use. Make sure all functions are turned off before connection to a power source or load.

EXTENSION CORDS

WARNING

• Use of improper extension cord could result in a risk of fire and electric shock. When using an extension cord, make sure that the pins of the extension cord are the same number, size and shape as those in the charger and be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
  
• When an extension cord is used, make sure that
  • a) the pins of the extension cord are the same number, size, and shape as those in the charger,
  •  b) the extension cord is properly wired and in good electrical condition,
  •  c) the wire size is large enough for the AC rating of the charger.
• CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE Pull the extension cord by the plug rather than the cord when disconnecting from the built-in 120-volt AC charger or the AC outlet.

SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS

WARNING: BURST HAZARD

• Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage property. Use the unit for charging/boosting a lead-acid battery only. It is not intended to supply power to a low-voltage electrical system other than in a starter-motor application.
• Use of an attachment not supplied, recommended or sold by manufacturer specifically for use with this unit may result in a risk of electrical shock and injury to persons.

WARNING: RISK OF EXPLOSIVE GASES

• Working in the vicinity of a lead acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason, it is of the utmost importance that each time before using the jump-starter you read this manual and follow instructions exactly.
• To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and
  manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary markings on these products
  and on the engine.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE

• NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting, read the vehicle’s owner’s manual to confirm that external-starting assistance is suitable.
• When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.
• Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin.
• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station
• Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.
• Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid battery. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal object, to skin, causing a severe burn.
• Do not wear vinyl clothing when jump-starting a vehicle. Friction can cause dangerous static-electrical sparks.
• Be extra careful to avoid dropping a metal tool onto the battery. It might spark or short-circuit the battery or another electrical part and could cause an explosion.
• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangerous sparks, power arcing and/or explosion.
• When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts away from moving vehicle parts.
• Never allow red and black clamps to touch each other or another common metal conductor — this could cause damage to the unit and/or create a sparking/explosion hazard.
• Make sure to connect the clamps with correct polarity. Damage caused by improper connection is not covered by the Warranty.
• Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Place this unit as far away from the battery as cables permit.
• Never allow battery acid to come in contact with this unit.
• Do not operate this unit in a closed area or restrict ventilation in any way.
• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt battery system.
• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a vehicle that does not have a battery installed.
• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.
• Do not use this jump starter on a watercraft. It is not qualified for marine applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.

SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS

WARNING: BURST HAZARD: Bursting articles can cause serious injury

• Carefully follow instructions on articles to be inflated.
• Never exceed the recommended pressure listed in instructions on articles to be inflated. If no pressure is given, contact article manufacturer before inflating.
• Always monitor the pressure on the LCD screen.

CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE

• Never leave the compressor unattended while in use.
• Do not operate compressor continuously for longer than approximately 10 minutes, depending on ambient temperatures. This could damage the compressor. Follow the instructions in the “Portable Compressor” section.

SPECIFIC SAFETY INSTRUCTIONS FOR THE USB POWER PORTS

• Do not insert foreign objects into the USB Power Ports.
• Do not attach USB hubs or more than one personal electronic device to each USB Power Port.
• Do not use this unit to operate appliances that require more than 6.2 amps in total to operate from the USB power ports

FIRST AID

• Skin: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek immediate medical attention.
• Eyes: If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention.
• LCD liquid crystal display: If liquid crystal comes in contact with your skin: Wash area off completely with plenty of water. Remove contaminated clothing. If liquid crystal gets into your eye: Flush the affected eye with clean water and then seek medical attention. If liquid crystal is swallowed: Flush your mouth thoroughly with water. Drink large quantities of water and induce vomiting. Then seek medical attention.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Congratulations on purchasing your new Stanley® FatMax® Professional Digital Power Station. Read this Instruction Manual and follow the instructions carefully before using this unit.

OVERVIEW

Common Actions and Unit Responses
The following actions turn the unit on and activate the LCD screen

Note: The unit will automatically power off once ALL the functions are turned off.

VIEWING BATTERY STATUS

• To check the unit’s battery charge level, press the Battery Status Button. The Battery Status Icon and Battery Voltage Indicator will display for 10 seconds (only), indicating the battery charge level as follows
  
• If the battery charge level is at full capacity, four solid bars will display.
• If the battery is partially charged, two or three solid bars will display.
• If the battery is nearly empty, one solid bar will display. The unit should be charged at this time.
• If the battery is completely empty, four blank bars will display. The unit MUST be charged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut down. The unit will not operate until the battery is recharged.
• Note: If no other actions are taken, the unit will automatically power off after 10 seconds.

CHARGING/RECHARGING

• Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All batteries lose energy from self discharge over time and more rapidly at higher temperatures. Therefore, batteries need periodic charging to replace energy lost through self-discharge. When the unit is not in frequent use, manufacturer recommends the battery should be recharged at least every
  30 days and after each use.
• Notes: This unit is delivered in a partially charged state – you must fully charge it before using it for the first time. Initial AC charge should be for 40 hours or until the Battery Status Icon shows 4 solid bars.
• Recharging the battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life. The battery can be recharged using the built-in 120 Volt AC Charger. Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
• CAUTION: RISK OF PROPERTY DAMAGE Failure to keep the battery charged will cause permanent damage and result in poor jump starting performance.
• IMPORTANT: If you know the unit is discharged, but the battery icon displays four solid bars as if the unit is fully charged when
  connected to a charging power source, this may be due to the internal battery having high impedance. The manufacturer suggests leaving the unit charging for a period of 40 hours using the built-in AC charger before use.

Charging/Recharging Using the Built-In 120 Volt AC Charger and AC Extension Cord

1. Lift the protective cover of the built-in 120 volt AC charger located on the lower left front of the unit (refer to the “Features” section to locate). Connect an extension cord to the unit. Plug the other end of the cord into a standard 120‑volt AC wall outlet. When the unit is properly connected to an AC power source, the LCD screen will display the following
   The bars on the Battery Status Icon represent the charge level of the unit’s internal battery. The bars on the Battery Status Icon will change from empty to solid (bottom to top) repeatedly to indicate the unit is charging. The backlight will turn on for 10 seconds (only).
2. Charge for approximately 40 hours or until the Battery Status Icon shows 4 solid bars.
3. When charging is complete, unplug the AC extension cord from the AC outlet and then disconnect it from the unit.

JUMP-STARTER

• This unit is equipped with a jump starter power switch that allows energy to flow only when proper connections are made to battery and frame.
  • a) For negative-grounded systems, connect the positive (red) clamp to the positive ungrounded battery post and the negative (black) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block.
  • b) For positive-grounded systems, connect the negative (black) clamp to the negative ungrounded battery post and the positive (red) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block.
• IMPORTANT: Make sure the Compressor Power Button has been turned off before attempting to use the unit as a Jump Starter

WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE

• FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE “Specific safety instructions for jump starters” section of this instruction manual.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or explosion.
• If the clamps are connected incorrectly with regard to polarity, the unit will sound a continuous alarm until the clamps are disconnected. The backlit LCD Screen will display the Battery Status Icon, the Battery Voltage Icon and the Clamp Icons. The“+” and”–” signs above the Clamp Icons, the Arrow Icons and the Alarm Icon will flash. The backlit LCD screen will display the following
  
• CAUTION: The unit will suffer permanent damage if the Jump Starter Power Switch is turned on while the clamps connected with reverse polarity. Disconnect the clamps and reconnect to battery with correct polarity.
• If the Jump Starter Power Switch is turned on and the unit detects that the clamps are not connected to a battery, a two second warning will sound every 10 seconds. The LCD screen will display the Battery Status Icon, the Battery Voltage Indicator, and the Clamp Icons with the “+” and”–” signs. The Alarm Icon and the Jump Starter Icon will flash. The backlit LCD screen will display the following
  Turn off the Jump Starter Power Switch; connect the clamps to the battery, making sure the clamps are connected with correct polarity then turn the Jump Starter Power Switch back on.
• Always disconnect the negative (black) jumper cable first, followed by the positive (red) jumper cable, except for positive grounded systems.

Procedure

Take the following steps, observing all cautions and warnings in the “Important Safety Instructions” section at the front of this manual.

1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place vehicle in “park” and set the emergency brake.
2. Make sure the jump-starter power switch is in the off position.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is connected to chassis)(MOST COMMON)
   • 4a) Connect positive (+) red clamp to vehicle battery’s positive terminal.
   • 4b) Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body part. Never clamp
     directly to negative battery terminal or moving part. Refer to the automobile owner’s manual
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
   Note: In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6.
   • 5a) Connect negative (–) black clamp to vehicle battery’s negative terminal.
   • 5) Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body part. Never clamp directly to positive battery terminal or moving part. Refer to the automobile owner’s manual.
6. When the clamps are connected properly, the unit will automatically turn on in jump-starter mode. The backlit LCD screen will display the following to indicate the unit is ready to jump-start
   The Battery Status icon, Battery Voltage Indicator, Clamp Icons and the “+” and”–” signs light solid. The jump starter icon will flash to indicate the clamps are properly connected
7. Turn the Jump-Starter Power Switch on. Turn on the ignition and crank the engine in 5-6 second bursts until engine starts. The backlit LCD screen will display the following
   The Battery Status Icon, the Battery Voltage Indicator, Jump Starter Icon, Clamp Icons and the “+” and”–” signs light solid to indicate the unit is jump-starting.
8. Turn the Jump-Starter Power Switch off.
9. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
   IMPORTANT: Always turn the unit off when not in use. Recharge this unit fully after each use.

CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE

• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before jump-starting this type of vehicle, read the vehicle manual to confirm that external-starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedure and look for other problems that need to be corrected.
• If vehicle fails to start, turn off the ignition, turn off the Jump-Starter Power Switch, disconnect the jump-start system’s leads and contact a qualified technician to investigate why the engine did not start.

ALTERNATOR CHECK

Set up the unit and connect to the battery following steps 1 through 5 in the “Jump-Starter” section.

PART 1

No Load (turn OFF all vehicle’s accessories): The vehicle battery must be fully charged before testing the alternator. Run the engine long enough to achieve normal idle speed and verify there is a no-load voltage.

1. Press the Alternator Check Button to start the check. The backlit LCD screen will display the following to indicate the unit is
   analyzing the alternator
   The Battery Status Icon will light solid and the Alternator Icon will flash.
2. If the unit detects that the alternator is good, the backlit LCD screen will display the following
   The Battery Status Icon, Alternator Icon, and “ALT GOOD” will light solid.
3. If the unit detects that the alternator is out of typical voltage range, the backlit LCD screen will display the following
   The Battery Status Icon, Alternator Icon and “ALT” will light solid. The Fault Icon will flash.
4. Press the Alternator Check Button again to stop the test and turn off the unit.

PART 2

Under Load (accessories ON): Next, load the alternator by turning on as many accessories as possible (except for A/C and Defrost).

1. Press the Alternator Check Button to start the check. The backlit LCD screen will display the following to indicate the unit is analyzing the alternator
   The Battery Status Icon will light solid and the Alternator Icon will flash.
2. If the unit detects that the alternator is good, the backlit LCD screen will display the following
   The Battery Status Icon, Alternator Icon, and “ALT GOOD” will light solid.
3. If the unit detects that the alternator is out of typical voltage range, the backlit LCD screen will display the following
   The Battery Status Icon, Alternator Icon and “ALT” will light solid. The Fault Icon will flash.
4. Press the Alternator Check Button again to stop the test and turn off the unit.

IMPORTANT: Always turn the unit off when not in use. Recharge this unit fully after each use.

Notes: The unit may detect that the alternator is out of typical voltage range because someone has added a number of accessory loads on the charging system, thereby increasing current demand from the alternator. MAKE SURE THAT THE ALTERNATOR IS RATED TO SUPPORT THE APPLICATION. This check may not be accurate for every make, manufacturer and model of vehicle. Check only 12 volt systems.

PORTABLE COMPRESSOR

The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. A nozzle adaptor is supplied that screws onto the end of the SureFit™ nozzle at the free end of the compressor hose. The compressor hose with tire fitting is stored in the compressor hose storage compartment. Refer to the “Features” illustration for locations of compressor hose. The Compressor Power Button and Compressor Pressure Control Buttons are located on the control panel on the front of the unit. Before proceeding, check the unit’s battery status on the LCD screen. Four solid bars in the battery icon indicates a full battery.

When the battery level is nearly empty with only one solid bar, the unit MUST be recharged before use or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut down. The compressor may be used by removing the air hose from the storage hatch and if required, fitting the nozzle adapter to the air hose. The compressor is capable of inflating up to 120 pounds per square inch (psi) pressure. The compressor can operate long enough to fill up to 3 average sized tires before the battery must be recharged. Return hose to the storage compartment after use.

IMPORTANT: Make sure the Jump Starter Power Button has been turned off before attempting to use the unit as a Compressor.

WARNING – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE. Follow all safety instructions found in the “Specific Safety Instructions For Compressors” section of this instruction manual.

CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE

When the compressor is operated at a low PSI, the unit may start in low and gradually rev up. When the compressor is operated at higher PSIs, the unit may operate normally for several minutes, then rev down for a few minutes before returning to normal operation. This feature protects the unit from overheating during normal use. In any event, do not operate compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient temperatures), as it may overheat. This could damage the compressor. If the compressor must be operated for longer periods: every 10 minutes press the Compressor Power Button to turn the compressor off, then restart after a cooling down period of approximately 30 minutes.

Inflating Tires or Products With Valve Stems

1. Screw the SureFit™ nozzle onto the valve stem. Do not overtighten.
2. Press the Compressor Power Button. A beep will sound and the backlit LCD screen will display the following
   The Compressor Icon will light and the digital display will alternately show the flashing pre-set psi value (that was last set by the compressor pressure control buttons) and the current pressure of the item being inflated (which will light solid).
3. Press the “+” and “–” Pressure Control Buttons to set the desired pressure from a range pre-set values (between 3 and 120), which will display on the backlit LCD screen. The unit will sound a beep with each press of the buttons (holding the button speeds up the upward or downward value selection). Once the desired pressure has been entered, release the button and the flashing digital display will show the new selected pressure, as follows
   The new selected value is now stored in the unit’s memory until it is manually reset.
4. Press the Compressor Power Button once more to begin inflating. The Compressor Icon will flash and the digital display will only show the current pressure value (which will light solid) to indicate the compressor is activated. Monitor the pressure on the LCD screen.
   IMPORTANT NOTE: To interrupt during inflation, press the Compressor Power Button again.
5. When desired pre-set pressure is reached, the compressor will automatically stop.
6. Press the Compressor Power Button again to turn off the unit.
7. Unscrew and remove the SureFit™ nozzle from the valve stem.
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose and SureFit™ nozzle in storage compartment.

Inflating Other Inflatables Without Valve Stems

Inflation of other items requires use of the nozzle adapter.

1. Screw the nozzle adapter into the SureFit™ nozzle. Do not overtighten.
2. Insert the nozzle adapter into item to be inflated.
3. Follow steps 2 through 4 of the “Inflating Tires or Products With Valve Stems” section.
   IMPORTANT: Small items such as volleyballs, footballs, etc. inflate very rapidly. Keep this in mind when setting pressure. Take extra care not to over-inflate.
4. When the desired pressure is reached, the compressor will automatically stop. Press the Compressor Power Button again to turn off the unit.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the SureFit™ nozzle.
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, SureFit™ nozzle and nozzle adapter in the storage compartment.

USB PORTS

The USB Power Button and the four USB Ports are located on the left hand side of unit. The USB Power/Fault Indicator is a translucent ring around each of the four USB Ports. Refer to the “Features” section to locate.
IMPORTANT NOTES:

• The top two USB Ports provide a total of 3.1A (5V each). The bottom two USB Ports provide a total of 3.1A (5V each). When the USB Ports are in use, the unit will monitor for the following USB fault conditions on all the USB Ports: thermal fault, low battery voltage fault, overload and short circuit. The USB Power/Fault Indicators are divided into an upper set and a lower set. The upper set detects fault conditions in the first two USB Ports; the lower set monitors in the last two USB Ports. If a fault condition exists in either of the first two USB Ports, the upper set of USB Power/Fault Indicators will flash blue. If a fault condition exists in either of the bottom two USB Ports, the lower set of USB Power/Fault Indicator will flash blue. In either case, the backlit LCD screen will continuously display the following
  
• The Fault Icon will flash. The USB Ports will automatically shut down. Should this occur, disconnect the USB-powered device and press the USB Power Button again to turn off the USB Ports immediately. Make sure the unit does not need to be recharged. Allow the unit to cool down for several minutes before attempting to use the USB Ports again. If a fault occurs again, make sure that the total draw of all USB devices plugged into the top two USB Ports does not exceed 3.1A and/or the total draw of all USB devices plugged into the bottom two USB Ports does not exceed 3.1A. If an individual USB device is within specifications and the fault occurs, have the USB device checked for malfunction and do not continue to use it with these USB Ports.

Using the USB Ports

1. Press the USB Power Button to turn on all four USB Ports. A beep will sound, the USB Power/Fault Indicators around each of
   the four USB Ports will light blue and the backlit LCD screen will continuously display the following
   The Battery Status Icon and Battery Voltage Indicator will light solid, as well as the USB Icon, indicating the USB ports are ready to use.
2. Plug the USB-powered device into the USB power port(s) and operate normally.
3. Press the USB power button again to turn off the USB Ports.

Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in the battery icon indicates a full battery. When the battery level is nearly empty with only one solid bar or completely empty with 4 empty bars, the unit must be recharged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut down.

IMPORTANT: Make sure the USB Ports are turned off when the unit is being recharged or stored.

Notes: This unit’s USB Ports do not support data communication. They only provide power to external USB-powered devices. The top two USB Ports provide a total of 3.1A (5V each). The bottom two USB Ports provide a total of 3.1A (5V each). Some household USB-powered electronics will not operate with this unit.

LED AREA LIGHT

The built-in 3-LED area light is controlled by the Area Light Power Button on the control panel (refer to the “Features” section to locate). Press the Area Light Power Button once to turn the light on. Press the Area Light Power Button again to turn the area light off.

IMPORTANT: When the Area Light Power Button is pressed to turn it on, a beep will sound. The backlit LCD screen will turn on for 10 seconds (only) and will then continuously display the Battery Status Icon and the Battery Voltage Indicator. Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in the battery icon indicates a full battery. When the battery level is nearly empty with only one solid bar or completely empty with 4 empty bars, the unit must be recharged at this time or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut down.

IMPORTANT: Make sure the Area Light is turned off when the unit is being recharged or stored.

CARE AND MAINTENANCE

• All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we recommend that the battery is charged at least every 30 days.
• Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild solution of water and detergent.
• There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact the manufacturer to replace any components that have become worn or broken.

Battery replacement/disposal

BATTERY REPLACEMENT

• The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact the manufacturer for any information you may need

SAFE BATTERY DISPOSAL

• Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is required. Failure to comply with local, state and federal regulations can result in fines or imprisonment. Please recycle.

WARNINGS

• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.

TROUBLESHOOTING

Unit will not charge

• Make sure all of the unit’s functions are turned off.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.

Unit fails to jump-start

• Make sure unit’s Jump Starter Power Switch is in the on position.
• Make sure a proper polarity cable connection has been established.
• Make sure the unit is not being operated in the Compressor mode.
• Check that the unit has a full charge. Recharge the unit if necessary.

Portable compressor will not inflate

• Make sure the Compressor Power Button has been pressed to turn the compressor on.
• Make sure the unit is not being operated in the Jump Starter mode.
• Make sure the SureFit™ nozzle is securely screwed on to the valve stem when attempting to inflate tires; or that the nozzle adapter is securely screwed into the SureFit™ nozzle and is inserted properly into the item to be inflated on all other inflatables.
• Check that the unit has a full charge. Recharge the unit if necessary.

USB power port will not power appliance

• Make sure the USB Power Button is in the on position.
• Make sure all the USB Power/Fault Indicators light solid blue. If a fault condition exists in either of the first two USB Ports, the upper set of USB Power/Fault Indicators will flash blue. If a fault condition exists in either of the bottom two USB Ports, the lower set of USB Power/Fault Indicator will flash blue. Refer to the Important Notes in the “USB Ports” section to remedy any faults.
• Make sure that the total draw of all USB devices plugged into the top two USB Ports does not exceed 3.1A and/or the total draw of all USB devices plugged into the bottom two USB Ports does not exceed 3.1A.
• Some USB-powered household electronics will not operate with this USB charging/power port. Check the manual of the corresponding electronic device to confirm that it can be used with this type of USB charging/power port.
• Check that the unit has a full charge. Recharge the unit if necessary.

LED area light does not come on

• Make sure the area light power button is in the on position
• Check that the unit has a full charge. Recharge the unit if necessary.
  

ACCESSORIES

• Recommended accessories for use with your tool may be available from the manufacturer. If you need assistance regarding accessories, please contact the manufacturer at (877) 571-2391.
• WARNING: The use of any accessory not recommended for use with this appliance could be hazardous

SERVICE INFORMATION

• Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at (877) 571-239

ONE-YEAR LIMITED WARRANTY

• The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty Period”). If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways
  • 1) Return the product to the manufacturer for repair or replacement at manufacturer’s option. Proof of purchase may be required by manufacturer.
  • (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
• This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents damages sustained during shipping alterations unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product. This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to state or province to province. This product is not intended for commercial use.
• Please complete the Product Registration Card and return within 30 days from purchase of the product to Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432. Baccus Global LLC, toll-free number: (877) 571-2391.

SPECIFICATIONS

• Boost Ampere: 12V DC, 1,000A peak battery, 500A instant
• Battery type: Maintenance-free, sealed lead acid, 12Vdc, 17Ah
• AC input: 120V AC, 60Hz, 13W
• Area light: 3 white LEDs
• USB ports: 5V DC each, 6.2A total (3.1A total in the top two USB Ports; 3.1A total in the bottom two USB Ports)
• Compressor maximum pressure: 120 PSI

For more manuals by Stanley Fatmax, visit ManualsLibraryy

Stanley Fatmax PP1DCS 1000 Peak Amp Power Station-FAQs