Euhomy IM-F Countertop Icemaker Machine Instruction Manual

Euhomy IM-F Countertop Icemaker Machine

Safety Precautions

IMPORTANT SAFETY TIPS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.

• Do not operate this, or any other appliance with a damaged cord.
• If the supply cord is damaged, it must be replaced by the manufacturer its service agent, or a similarly qualified person in order to avoid hazard. This ice-maker must be positioned so that the plug is accessible.
• Connect to properly polarized outlets only other appliances should be plugged into the same outlet.
• Be sure that the plug is fully inserted into the receptacle.
• Do not run the power cord over carpeting or other heat insulators.
• Do not cover the cord. Keep the cord away from traffic areas, and do not submerge in water. We do not recommend the use of an extension cord, as it may overheat and become a risk of fire.
• If you must use an extension cord, use No.14AWG minimum size and rated no less than 1875 watts.
• Unplug the icemaker before cleaning or making any repairs or servicing. Exercise caution and use reasonable supervision when the appliance is used near children.
• Do not use your ice maker outdoors.
• Place the ice-maker away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and wall.
• Keep a minimum distance of 4 inches on each side of your unit free.
• Do not use other liquids to make the ice cube other than water.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
• Do not tip over. If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room temperature before plugging it in.
• Do Not Use Mechanical Devices To Defrost IceMaker. Do Not Puncture Refrigerant Tubing.
• To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing Consult RepairManual/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.
• Dispose Of Property In Accordance With Federal Or Local Regulations.
• Follow Handling Instructions Carefully.
• The ice maker should be installed in accordance with the safety standards for Refrigeration Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.
• If the unit is with problem needs to be maintained, and replaced with like components, and that servicing shall be done by factory-authorized service personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper service.

Operation & Installation

ASSEMBLY AND PARTS

1. Water reservoir cover
2. Unit top cover
3. Water separator pipe
4. Evaporator
5. Ice basket
6. Ice scoop
7. Transparent window
8. ControlPanel:
   1. Timer button
   2. Power button
   3. LCD Display area
      1. Ambient temp and ice-making countdown symbol: when the display shows <M>, it ice-making countdown, when the display shows <℉>， means ambient temp.
      2. Ice making and Ice harvest symbol: when the symbol is 1 running, the unit is making ice cubes, when the symbol flashes, the unit is ice harvest.
      3. ON/OFF symbol.
      4. Error code E 1-Ambient temp sensor breakdown. E 2-refrigerating tube sensor breakdown
      5. Lack water warning symbol.
      6. Ice full warning symbol.
      7. Time setting display area. When show<H>， timer unit ON/OFF， when show<M>， setting ice making time.
   4. Ice making and timer reduction.
   5. ice making and timer increase.
9. Hot Air Outlet
10. Water draining port: To drain out the water from the unit.

UNPACKING YOUR ICE MAKER

• Remove the exterior and interior packaging. Check that the ice basket and ice scoop is included If any parts are missing, please contact our customer service.
• Clean the interior with lukewarm water and a soft cloth. Take out the ice basket and clean it.
• Find a location for your ice maker that is protected from direct sunlight and other sources of heat(ie. stove, furnace, radiator ). Place the ice maker on a level surface. Make sure that there is at least 6 inches of space between the back and sides of your ice maker and the wall.
• Allow one hour for the refrigerant fluid to settle before plugging the icemaker in.
• The appliance must be positioned so that the plug is accessible.

CONNECTING YOUR ICE MAKER

• This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug that mates with standard three-prong wall outlets to minimize the possibility of electric shock
• Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and /or grounding should be directed toward a certified electrician.
• This appliance requires a standard 110-120volt, 60Hz electrical outlet with three-prong ground.

OPERATION PANEL AND DISPLAY AREA

• Remove the cover of the water reservoir and pour potable water into the water reservoir. And be sure to keep the water level below the max. level with a FULL mark displayed in the following picture. Then move back the cover at once to avoid foreign matter entering.

NOTES:

• Do not pour the water into the internal water tank located underneath the ice basket. This tank is not big enough and will affect the ice-making performance.
• When you plug the unit, the power symbol<>will fash. Press the <ON/OFF> button, the unit will start making ice cubes, ice making symbolwill keep running. The left-up corner of the display area will show the ambient temp, i.e:80℉means the ambient temp is 80 ℉. After several mins, this area will show a flash number, and the ice-making will countdown, i.e:10M means the ice-making will finish 10 mins later.
• When the ice maker harvests, symbolflash, the water will flow from the top water reservoir to the bottom water tank through the solenoid valve, the symbolwill be on, when the water in the bottom water tank is full, the symbolwill be off, then the next ice making cycle starts again. When there is no water in the water reservoir, the symbolwill keep on. Turn off the unit and fill the water again, then restart the unit to make an ice cube. Or fill the water directly and wait 20 minutes, the unit will restart.
• Remark: The ice-making cycle lasts about 13 to 25 minutes, depending on the ambient temperature. And for the first time, according to the initial water temperature, ice-making last time will be a little longer. In extremely hot room temperatures, ice-making time may vary a lot, but it will not exceed 35 minutes. If you think the ice cube is not thick enough, during ice-making, press the<+>and<->to set the ice making lead time. Press one time and the ice-making cycle will increase or Reduce by one minute, 6 most. This can only start from the new cycle.
• When the Ice Full symbolis on, the unit will stop, take out the ice cube inside, and the unit will start working again. If press the button<ON/OFF>more than 5s, when the ice maker is working, the unit will start harvesting. Press the button<ON/OFF>, the unit will turn off. Timer setting. Unit on timer setting, When the unit is working, the timer setting the unit off. Unit off Time setting, When the unit is off, timer the unit on. Press the<TIMER>button, the display will show<1H>, and then press <+> and <-> to set the time. During the setting, the H is flash, after 5s, the H will keep on and the unit will be in your Timers setting…
• Water Drain: take off the drain plug cap on the back of the unit, take out the silicon plug, and then drain the water inside. It is better that exchange water every 24 hours. and clean the unit every 3days.

Notes

• Make sure the water tank, water filter, and water separator pipe is not blocked, clean them.
• The water temp will affect the ice-making capacity. The lower temp, the more ice cubes are produced.
• The cooler the ambient temp, the more ice cubes produce.
• Always use good quality water to make sure the pump works well. Bad quality water will cause pump noise but doesn’t affect the unit working .
• The compressor restarts 3 minutes later if you turn off the unit.

Tips & Maintenance

CLEANING AND MAINTAINING YOUR ICE MAKER

Before using your ice maker, it is strongly recommended to clean it thoroughly.

• Take out the ice basket.
• Clean the interior with diluted detergent, warm water, and a soft cloth
• Then use the water to rinse the inside parts, and drain out the water from the draining port by unplugging the drain capon the back
• The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
• Dry the interior and exterior with a soft cloth.
• When the machine is not in use for a long time, open the water drain cap to drain water completely out from the water reservoir.
• After using your ice maker for a long time, we also suggest you should clean your unit. Especially to the water separator pipe and the water filters, you must clean them periodically.
• If the water separator pipe is blocked and there is no water flowing down when you hear the compressor and the water pump inside are still working, please turn off the unit first disassemble this pipe, and clean it. Clean each hole on the pipe wall displayed in the following picture After cleaning, install back the water separator pipe and be sure the right terminal of the pipe connects to the silicone pipe well and as original.
• For both of the water tank and the big water reservoir, clean them with diluted detergent, warm water, and a soft cloth. Then use the water to rinse the inside, and drain out the water from the draining port by unplugging the drain cap on the back. It will help you keep the unit and ice cube hygienically and also make the unit work normally.
• When cleaning, if find that the ice cube is left on the evaporator and can not be taken out easily, you can turn on the unit to let the nit enter the ice-making process, then push the/OF “button for more than 5 seconds to let the unit start ice harvest process to melt the ice cube. It will help you remove the hard ice cube.
• How to drain out the water from the internal tank and big water reservoir completely. Because the water in the big water reservoir is stopped at to drain port by the water valve, if you want to drain away all the water, please plug on the unit but don’t start the unit, then remove the drain port cap at the back. Wait some minutes, all of the water will flow out.

Specfcations

TECHNICAL PARAMETERS

CIRCUIT DIAGRAM

Warranty

Euhomy offers a limited 1-year warranty (“ warranty period” ) on all of our products purchased new and unused from Euhomy company, with original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period. The warranty does not apply where damage is caused by other factors, including without limitation:

• normal wear and tear;
• abuse, mishandling, accident, or failure to follow operating instructions;
• exposure to liquid or infiltration of foreign particles;
• servicing or modifications of the product other than by Euhomy;
• commercial or non-household use.

The Euhomy warranty covers all costs related to restoring the proven defective product through repair or replacement of any defective part and necessary labor so that it conforms to its original specifications. A replacement product may be provided instead of repairing a defective product. Euhomy’s exclusive obligation under this warranty is limited to such repair or replacement. A receipt indicating the purchase date is required for any claim, so please keep all receipts in a safe place. Although greatly appreciated, product registration is not required to activate any warranty, and product registration does not eliminate the need for the original proof of purchase. The warranty becomes void if attempts at repair are made by non-authorized third parties and/or if spare parts, other than those provided by Euhomy, are used. You may also arrange for service after the warranty expires at an additional cost. These are our general terms for warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you have an issue with a Euhomy product, please contact us (euhomy@hotmail.com), and we will do our best to resolve it for you.

For more manuals by Euhomy, visit ManualsLibraryy

Euhomy IM-F Countertop Icemaker Machine-FAQs