Honeywell Focuspro 5000 Non-Programmable Digital Thermostat
Read and save these instructions.
For help please visit yourhome.honeywell.com
Thermostat controls
Display screen
Auto changeover (heat/cool)
Auto Changeover is a feature used in climates where both air conditioning
and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation (called “deadband”).
The 3-degree separation between heating and cooling set temperatures is fixed, and cannot be changed.
- Press system button until screen displays “Auto”.
NOTE: The Auto system setting may not appear, depending on how your thermostat was installed
Built-in compressor protection
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
Battery replacement
- Batteries are optional (for backup power) if your thermostat was wired to run on AC power when installed.
- Install fresh batteries when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted.
- Replace batteries once a year, or before leaving home for more than a month. All settings are permanently stored in memory, and do not require battery power.
Customer Assistance
For assistance with this product, please visit yourhome.honeywell.com.
Or call Honeywell Customer Care toll-free at 1-800-468-1502
CAUTION
Equipment damage hazard
To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Accessories/replacement parts
To order, please call Honeywell Customer Care toll-free at 1-800-468-1502.
TH5110D
- Battery holder ………………………Part No. 50000951-001
- Cover plate assembly* …………..Part No. 50001137-001
- Cover plate assembly* …………..Part No. 50002883-001
TH5320U/TH5220D
- Battery holder ………………………Part No. 50007072-001
- Cover plate assembly* …………..Part No. 50002883-001
*Use to cover marks left by old thermostats.
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- make sure fresh AA or AAA alkaline batteries (depending on model) are correctly installed (see page 3).
Heating or cooling system does not respond
- Press SYSTEM button to set system Heat (see page 2). Make sure the temperature is set higher than the Inside temperature.
- Press SYSTEM button to set system to Cool (see page 2). Make sure the temperature is set lower than the Inside temperature.
- Check circuit breaker and reset if necessary.
- Make sure power switch at heating & cooling system is on.
- Make sure furnace door is closed securely.
- Wait 5 minutes for the system to respond.
Temperature settings do not change
Make sure heating and cooling temperatures are set to acceptable ranges:
- Heat: 40° to 90°F (4.5° to 32°C).
- Cool: 50° to 99°F (10° to 37°C).
“Cool On” or “Heat On” is flashing
- Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor (see page 3).
5-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,
- return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
- call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Toronto, Ontario M1V4Z9.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
yourhome.honeywell.com
For more manuals by Honeywell, visit ManulsLibraryy
Honeywell Focuspro 5000 Non-Programmable Digital Thermostat-FAQs
How does a non-programmable thermostat work?
A non-programmable thermostat, also called a manual thermostat, lets you manually set the temperature and control heating or cooling without scheduling. You adjust the temperature as needed.
How do I operate my digital thermostat?
To use your digital thermostat, read the user manual, set the time and date, and adjust the temperature as desired. Non-programmable models like the FocusPro 5000 don’t require programming a schedule.
How do I troubleshoot my digital thermostat?
For troubleshooting, you can reset the thermostat, clean off dust or corrosion, check power and wiring, or adjust settings. Consult the manual for specific steps.
Does my thermostat need power to function?
Yes, the thermostat requires constant power, usually supplied by a common wire (c-wire) in the HVAC system, which is necessary for it to operate effectively.
Is it necessary to program my thermostat?
Non-programmable thermostats don’t have scheduling features. Instead, they allow for manual temperature adjustments at any time, making them ideal for spaces where constant temperature control is desired.
How is the temperature detected by the thermostat?
The thermostat’s sensor detects temperature changes through a bimetallic strip or internal sensor, which then regulates heating or cooling based on your set temperature.
What are the basic settings on my thermostat?
The FocusPro 5000 has heating and cooling settings. Use “Heat” for warming and “Cool” for air conditioning. Adjust the temperature to your comfort level.
How can I test if my thermostat is working correctly?
You can turn it on to see if it heats or cools the room as expected, use an indoor thermometer to compare temperatures, or test with a multimeter for electrical continuity.
Does my thermostat require batteries?
Yes, thermostats often need batteries for operation, even if they connect to a power source, as the batteries provide backup power and support certain functions.
Can I replace the thermostat without turning off the power?
No, always turn off power to your HVAC system before replacing a thermostat to prevent electrical hazards or damage to the system.