NutriBullet NBR-1201 12-Piece High-Speed Blender User Manual

NutriBullet NBR-1201 12-Piece High-Speed Blender

What’s included?

Assembly guide

PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE NUTRIBULLET®:

• Make sure the base is plugged in for use.
• Handle the extractor blade assembly with care, as the blades are sharp.
• Never run the NutriBullet® while empty.
• NutriBullet® accessories are not intended to be used in the microwave, as it may damage the accessories.
• Never leave the NutriBullet® unattended while in use.

NutriBullet® cup assembly & use.

1. Review all warning and caution statements in the Important Safeguards section (pg. 2-7) before proceeding to Step 2.
2. Place the motor base on a clean, dry, level surface such as a counter or table.
3. Add ingredients and liquid to the NutriBullet® cup. 
4. Place the extractor blade onto the cup and twist until it is tightly sealed
5. Plug the power cord into an electrical outlet.
   
6. Turn the cup upside down and place it onto the motor base. Gently push and twist.   
7. Unlock the assembly by gently pushing and untwisting the cup counterclockwise.
   

Care & maintenance.

STEP 1: The most important thing is ALWAYS UNPLUG the motor base from the power
supply outlet when it is left unattended, before assembling, disassembling, changing accessories, or approaching parts that move in use, or when cleaning. Do not attempt to handle the appliance until all parts have stopped moving!
STEP 2: Remove the cup/extractor blade assembly from the motor base.
STEP 3: Clean the individual components (motor base, extractor blades, NutriBullet® cups) as follows:

MOTOR BASE:

• For the most part, the motor base doesn’t really get dirty, but if you neglect to twist the extractor blade onto the cup tightly, liquids can leak out and get into the base and stick to the activator buttons.
• To avoid the risk of injury, NEVER use your hands or utensils to clean the white actuator Tabs while the NutriBullet® is plugged in.
• Do not remove the rubber or plastic liners inside the motor base.
• Use a sponge or dish cloth dampened with warm, soapy water to wipe down the inside and outside of the motor base until clean.
• Pay particular attention to the white Actuator Tabs on the inside of the motor
  base to loosen any sticky debris from drips and spills. If necessary, you may use a
  small brush to scrub the area to ensure it is kept clean

EXTRACTOR BLADE:

• DO NOT REMOVE THE GASKET, as this will permanently damage the extractor blade and cause leakage. If, after washing as indicated above, additional disinfecting is desired, you may rinse with a 10% vinegar/water solution or with lemon juice. If, over time, the gasket becomes loose or damaged, you may order a new extractor blade at NutriBullet.com or contact Customer Service.
• Dry the extractor blade completely. It is helpful to turn the blade on its side in
  Your dish drainer to ensure BOTH SIDES of the extractor blade are completely dried.

NUTRIBULLET® CUPS & TO-GO LIDS:

• These items are all TOP RACK dishwasher safe. We recommend rinsing them and giving them a quick brush with a dish brush to remove any dried debris before washing them in the dishwasher. NEVER use the sanitize cycle to wash the Cups as this may warp the plastic.
• Regularly check the 3 tabs on the side of the Cup (cracking, crazing, breakage, or rounding). If damaged, replace immediately to prevent possible personal injury.

STUBBORN CLEAN UP:

• If ingredients dry inside the NutriBullet® Cup, make your cleanup a snap by filling the cup about 2/3 full with room temperature (21°C/70°F or less) water and screw on the extractor blade. Place the cup/extractor blade assembly on the NutriBullet.®
  Motor base for about 20-30 seconds. This will loosen the stuck ingredients, and with a light scrub and rinse, you’ll be all finished.

FOR MORE MANUALS BY NUTRIBULLET, VISIT MANUALSLIBRARYY

NutriBullet NBR-1201 12-Piece High-Speed Blender