Stinger WD20250 Vacuum Cleaner User Manual

Stinger WD20250 Vacuum Cleaner

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of common sense, staying alert, and knowing how your Wet/Dry vacuum cleaner (“Vac”) works.

Safety Signal Words

 DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

 WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

 CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, or property damage.

When using your vacuum, always follow basic safety precautions, including the following:

 WARNING- To reduce the risk of fire, electric shock, or injury:

• Read and understand this manual and all labels on the vacuum before operating.
• Use only as described in this manual.
• Do not leave the vacuum running while unattended – you may fail to notice important signs indicating abnormal operation, such as loss of suction, debris/liquid exiting the exhaust, or abnormal motor noises. Immediately stop using the vacuum if you notice these signs.
• Do not leave the vacuum when plugged in. Unplug from the outlet when not in use and before servicing.
• Sparks inside the motor can ignite flammable vapors or dust. To reduce the risk of fire or explosion, do not vacuum or use near flammable or combustible liquids, gases, or dusts, such as gasoline or other fuels, lighter fluid, cleaners, oil-based paints, natural gas, coal dust, magnesium dust, grain dust, aluminum dust, or gun powder.
• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not vacuum drywall dust, cold fireplace ash, or other fine dusts, which may pass through the filter bag and be exhausted back into the air.
• To reduce the risk of inhaling toxic vapors, do not vacuum or use near toxic or hazardous materials.
• To reduce the risk of electric shock, do not expose to rain or allow liquid to enter the motor compartment. Store indoors.
• Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with a torn filter or without the filter installed except when vacuuming liquids as described in this manual. Dry debris ingested by the impeller may damage the motor or be exhausted back into the air.
• Turn off the vacuum before unplugging.
• To reduce the risk of injury from accidental starting, unplug the power cord before changing or cleaning the filter.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not use with a damaged cord, plug, or other parts. If your Vac is not working as it should, has missing parts, has been dropped, damaged, left outdoors, or dropped into water, call customer service.
• Do not pull or carry by cord, use cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum over the cord. Keep the cord away from heated surfaces.
• Do not handle the plug, switch, or the vacuum with wet hands.
• Use only extension cords that are rated for outdoor use and have a grounding conductor. Extension cords in poor condition or too small in wire size can pose fire and shock hazards. To reduce the risk of these hazards, be sure the cord is in good condition and that the liquid does not contact the connection. Do not use an extension cord with conductors smaller than 16 gauge (AWG) in size. To reduce power loss, use a 14-gauge extension cord if 25 to 50 ft. long and 12 12-gauge for 50 ft. or longer.
• Connect only to a properly grounded outlet. See grounding instructions.
• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked; keep free of dust, lint, hair, or anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• To reduce the risk of falls, use extra care when cleaning stairs.
• To reduce the risk of personal injury or damage to Vac, use only Stinger-recommended accessories.
• When using as a blower:
  • Direct air discharge only in the work area.
  • Do not direct air at bystanders.
  • Keep children away when blowing.
  • Do not use a blower for any job except blowing dirt and debris.
  • Do not use as a sprayer.
  • Wear safety eyewear.
• To reduce the risk of eye injury, wear safety eyewear. The operation of any utility vacuum or blower can result in foreign objects being blown into the eyes, which can result in severe eye damage.

Introduction

This vacuum is intended for household use. It may be used for light vacuuming of wet or dry media and may also be used as a blower. The lightweight design allows usage for most small household vacuuming chores. Familiarize yourself with the following product features and read the entire owner’s manual for specific usage of your new Wet/Dry Vac.

Checking Carton Contents

Remove the entire contents of the carton. Check each item against the Carton Contents List. Contact 1-800-474-3443 if any parts are damaged or missing.

Carton Contents Lists

* Replacement filters and retainer band (already assembled)

Replacement filters are sold by Stock No. VF2000. They are available where you purchased your Stinger Vac.

Getting to Know Your Vac

Cord Storage

1. Your Wet/Dry Vac has a convenient area to store your power cord while not in use.
2. Coil the power cord around the handle in the recesses provided in the power head assembly.

Accessory Storage

Accessory storage is provided on the rear of the unit. Clip the accessory into the bracket from the side as shown.

Hose Storage

Drum has recesses on each side for hose storage.

Grounding Instructions

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

 WARNING:

Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like he plug shown. A temporary adaptor that looks like the adaptor shown may be used to connect this plug to a 2-pole receptacle, as shown. If a properly grounded outlet is not available, the temporary adaptor should be used only until a properly grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.

NOTE: In Canada, the use of a temporary adaptor is not permitted by the Canadian Electrical Code.

Operation

 WARNING: To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave the vacuum running while unattended – you may fail to notice important signs indicating abnormal operation, such as loss of suction, debris/liquid exiting the exhaust, or abnormal motor noises. Immediately stop using the vacuum if you notice these signs.
• Do not leave the vacuum plugged in when not in use.
• Do not continue running when the float has cut off suction.
• Do not operate the vacuum in areas with flammable gases, vapors, or explosive dust in the air. Sparks inside the motor can ignite airborne flammables. Flammable gases and vapors include: lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, or aerosol sprays. Flammable dusts include: coal, magnesium, aluminum, grain, or gun powder.
• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.
• Do not use a vacuum as a sprayer.

 WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter the motor compartment. Store indoors.
• Do not handle the plug, switch, or vacuum with wet hands.
• Do not service the vacuum while it is plugged in. If your vacuum is not working as it should, has missing parts, has been dropped, damaged, left outdoors, or dropped into water, return it to an independent service center or call customer service.
• When using an extension cord, use only outdoor-rated cords that are in good condition. Do not allow the connection to come into contact with liquid.
• Do not vacuum toxic materials to reduce the risk of inhaling the vapors or dust.

Your two-and-a-half-gallon Wet/Dry Vac is assembled at the factory and ready for use when you remove it from the carton. The unit is ready for dry vacuuming or blowing. After you plug the power cord into the outlet, turn the unit on by pushing the switch from position “O” to position “l”. The symbols used on the switch actuator are international “On & Off” symbols:

Vacuuming Dry Materials

1. The filter must always be in the correct position to reduce the risk of leaks and possible damage to the vacuum. Make sure that the filter is completely covering the filter cage and that the retainer band is as close to the lid as possible. Make sure there are no gaps between the filter and the lid. (See illustration). It is very important to assemble the filter to the cage without allowing any possible leaks or tears. Any leaks will allow the picked-up media to be blown out of the blower port and back into the surrounding environment.
2. To maintain peak performance of your vacuum when picking up small debris such as sawdust, it may be helpful to empty the dust drum and clean or replace the filter at more frequent intervals.
   NOTE: The filter should be dry to pick up dry material. If you use your vacuum to pick up dry debris when the filter is wet, the filter will clog quickly and be very difficult to clean. In case the filter gets wet, replace it before continuing dry pickup.

Vacuuming Liquids

1. Removal of the filter is highly recommended for wet pickups.
2. This Wet/Dry Vac is equipped with a float mechanism that will rise automatically to cut off the airflow when the liquid in the drum reaches a predetermined level. When this happens, turn off the vacuum, unplug the power cord, and empty the dust drum. You will know that the float has shut the airflow off because the suction ceases and the motor noise becomes higher in pitch, due to increased motor speed. The liquid capacity may vary with the rate of pickup.
3. Be sure to replace the filter after wet pickup. Never pick up dry debris without the filter properly installed.
   IMPORTANT: To reduce the risk of damage to the Vac, do not run the motor with the float in the raised position.

WARNING: Never leave the vacuum running while unattended.

Emptying the Drum

WARNING: To reduce the risk of injury from accidental starting, unplug the power cord before emptying the drum.

1. Place the Vac squarely on a stable surface, such as the ground, floor, bench, etc.
2. Remove the power head assembly of the Wet/Dry Vac by pulling outward on the latches located on each side of the vacuum. Lift off the power head assembly.
3. Dump the drum contents into the proper waste disposal container.

Blowing Feature

Your vacuum contains a blowing feature. It can blow sawdust and other debris. It is excellent to use to blow dust and debris out of garages or off patios and driveways. Follow the steps below to use your vacuum as a blower.

1. Locate the blowing port of your vacuum.
2. Insert one end of the 4-foot x 1-1/4 inch hose into the blowing port.
3. Turn the Vac “ON” and you are ready to use your Vac as a blower.

WARNING: Always wear safety goggles complying with ANSI Z87.1 (or in Canada, a CSA Z94.3) when using as a blower.

WARNING: To avoid injury to bystanders, keep them clear of blowing debris.

CAUTION: Wear a dust mask if blowing creates dust that might be inhaled.

CAUTION: To reduce the risk of hearing damage, wear ear protectors when using the Vac/Blower for an extended time or in a noisy area.

Maintenance

Filter

Your filter should be cleaned often to maintain peak vacuum performance.

NOTE: The filter is made of high-quality material designed to stop small particles such as sawdust. Handle the filter carefully when removing to clean or installing a new filter. Do not tear the filter during removal or installation if your intent is to reuse the filter.

Easy to Replace Filter

1. Extend the retainer band around the plastic posts on the lid.
2. Remove the filter bag from the filter cage.
3. Place the replacement filter on the filter cage until the open end touches the bottom of the lid.
4. Release the retainer band from the plastic post on the lid, holding the filter bag secure to the lid.
5. Make sure the retainer band is positioned on the filter bag covering the black printed line.

IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the filter before using the vacuum for dry material pick-up.

Take the dirty filter to a disposal container and gently brush away small dirt particles that may be adhering to the filter material.

IMPORTANT: After cleaning, check the filter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can allow a lot of dust to come out of your vacuum. Replace it immediately.

Installation

Before installing the filter on the vacuum, clean the area of the lid so that the retainer band will seal the bag against the lid and stop small particles from bypassing the filter bag.

If the filter is clean and not damaged, replace it in the filter cage. If it cannot be reused, place a new filter over the filter cage.

Replace the retainer band around the filter. Make sure the retainer band is positioned on the filter, and the filter completely covers the filter cage. Also, make sure the edges of the filter are completely secured under the retainer band.

NOTE: Clean the filter in an open area. Cleaning should be done outdoors and not in the living quarters.

 WARNING: Do not remove the filter cage and float. The float prevents liquid from entering the impeller and damaging the motor. The cage prevents fingers from touching the moving impeller.

Cleaning

To keep your Wet/Dry Vac looking its best, clean the outside with a cloth dampened with warm water and mild soap.

To clean the drum

1. Dump debris out.
2. Wash the drum thoroughly with warm water and mild soap.
3. Wipe out with a dry cloth.

Storage

Before storing your vacuum, the dust drum should be emptied and cleaned. The cord should be wrapped around the unit, and the hose should be stored as described in the cord/hose storage section in this manual. Accessories should be kept in the same area as the vacuum so they can be readily available. The vacuum should be stored indoors.

Troubleshooting

WARNING: If any of the power head assembly parts should become detached or broken, exposing the motor or any other electrical components, operation should be discontinued immediately to avoid personal injury or further damage to the vacuum. This vacuum has no user-serviceable parts.

Replacement Filter

Replacement filters are available where you purchased your vacuum. The stock number is VF2000.

Warranty

Model Number: WD20250

Full One-Year Warranty

If within one year from the date of purchase, this Wet/Dry Vac fails due to a defect in material or workmanship, Emerson will repair or replace it free of charge. This warranty does not cover filters, which are considered customer-replaceable parts. This product is not intended for commercial use. Warranty service is available by simply contacting Emerson.

Do not return the product to the store.

This warranty applies only to products purchased in the United States and Canada. This warranty gives you specific legal rights, and you may have other rights that may vary in the country (state or province) where you are situated.

Emerson
8100 West Florissant
St. Louis, MO 63136

Stock No. WD2025
Model No. WD20250

The model and serial number may be found on the left side of the vacuum top. You should record both the model and serial number in a safe place for future use.

QUESTIONS OR COMMENTS?

CALL: 1-800-474-3443

For more manuals by Stinger, visit ManualsLibraryy

Stinger WD20250 Vacuum Cleaner- FAQs