Sharp EL-1801P 2-Digit Serial Printing Calculator User Manual

Sharp EL-1801P 2-Digit Serial Printing Calculator

OPERATIONAL NOTES

To ensure trouble-free operation of your SHARP calculator, we recommend the following:

1. The calculator should be kept in areas free from extreme temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the calculator. Do not use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or store it where fluids, for example, water, can splash onto it. Raindrops, water spray, juice, coffee, steam, perspiration, etc., will also cause malfunction.
4. If service should be required, use only a SHARP servicing dealer, a SHARP-approved service facility, or SHARP repair service.
5. If you pull out the power cord to cut electricity completely, the present stored tax rate will be cleared.
6. Do not wind the AC cord around the body or otherwise forcibly bend or twist it.

OPERATING CONTROLS

POWER SWITCH; PRINT / ITEM COUNT MODE SELECTOR:

• “OFF”: Power OFF
• “•”: Power ON. Set to the non-print mode.
  P”: Power ON. Set to the print mode.
• P•IC”: Power ON. Set to the print and item count mode.
• For addition or subtraction, each time the + is pressed, 1 is added to the item counter, and each time the – is pressed, 1 is subtracted.
• The count is printed when the calculated result is obtained.
• Pressing of ∗, clears the counter.

Note: The counter has a maximum capacity of 3 digits (up to ±999). If the count exceeds the maximum, the counter will recount from zero.

ROUNDING SELECTOR:

Example: Set Decimal Selector to 2. 4 ÷ 9 = 0.444 …, 5 ÷ 9 = 0.555 …

GRAND TOTAL / RATE SETTING MODE SELECTOR

• “GT”: Grand Total
• “•”: Neutral
• “RATE SET”: Rate setting
• Enter the adding tax rate, then press.
• A maximum of 4 digits can be stored (decimal point is not counted as a digit).
• Only one rate can be stored. If you enter a new rate, the previous rate will be cleared.

DECIMAL / ADD MODE SELECTOR:

• “6 3 2 1 0”: Presets the number of decimal places in the answer.
• “F”: The answer is displayed in the floating decimal system.
• “A”: The decimal point in addition and subtraction entries is automatically positioned to the 2nd digit from the lowest digit of the entry number. Use of the add mode permits addition and subtraction of numbers without entry of the decimal point.
• Use of and will automatically override the add mode, and decimal correct answers will be printed.

SPECIFICATIONS

• Operating capacity: 12 digits
• Power source: AC: 120V, 60Hz
• PRINTING SECTION
• Printer: Mechanical printer
• Printing speed: Approx. 2.1 lines/sec.
• (At temperature 25°C (77°F), when “741.9 + ” is printed. The printing speed will vary with the number of rows and the figure types to be printed.)
• Printing paper: 57 mm(2-1/4″) – 58 mm(2-9/32″) wide 80 mm(3-5/32″) in diameter (max.)
• Operating temperature: 0°C – 40°C (32°F – 104°F)
• Power consumption: 65 mA
• Dimensions: 193 mm (W) × 256 mm (D) × 62.5 mm (H) (7-19/32″ (W) × 10-3/32″ (D) × 2-15/32″ (H))
• Weight: Approx. 1.0 kg (2.20 lb.)
• Accessories: 1 paper roll, 1 ink roller (installed), and an operation manual

CALCULATION EXAMPLES

1. Set the decimal selector as specified in each example. The rounding selector should be in the “5/4” position unless otherwise specified.
2. The grand total/rate set mode selector should be in the “•” position (off) unless otherwise specified.
3. The print/item count mode selector should be in the “P” position unless otherwise specified.
4. Press prior to beginning any calculation.
5. If an error is made while entering a number, press or and enter the correct number.
6. After entering a value, press or to activate the Cost/Sell/Margin Calculation mode. In case of performing different calculation tasks, the key must be pressed first to cancel the Cost/Sell/Margin mode.
7. Example procedures are listed in the following manner unless otherwise specified.

INK ROLLER REPLACEMENT

If printing is blurry even when the ink roller is in the proper position, replace the roller.

Ink roller: Type EA-772R

1. Set the power switch to OFF.
2. Remove the printer cover. (Fig. 1)
3. Hold the top of the ink roller and remove the roller by pulling it toward you and then upward. (Fig. 2)
4. Install the new ink roller in the correct position. Make sure that the roller is securely in place. (Fig. 3)
5. Put back the printer cover.

Cleaning the printing mechanism

If the print becomes dull after long-term usage, clean the printing wheel according to the following procedures:

1. Remove the printer cover and the ink roller.
2. Install the paper roll and feed it until it comes out of the front of the printing mechanism.
3. Put a small brush (like a toothbrush) lightly on the printing wheel and clean it by pressing.
4. Put back the ink roller and the printer cover.

Note: Do not rotate the printing mechanism manually; this may damage the printer.

PAPER ROLL REPLACEMENT

Never insert a paper roll if torn. Doing so will cause the paper to jam. Always cut the leading edge with scissors first.

1. Insert the leading edge of the paper roll into the opening. (Fig. 1)
2. Turn the power on and feed the paper by pressing. (Fig.2).
3. Lift the attached metal paper holder up and insert the paper roll into the paper holder. (Fig. 3)

ERRORS

There are several situations that will cause an overflow or an error condition. When this occurs, “E” will be displayed. The contents of the memory at the time of the error are retained. If an “0
E” is displayed at the time of the error, “– – – – – – –” will be printed in red and must be used to clear the calculator. Also, in rare cases, printing may stop midway, and the indication “E” appears on the display. This is not a malfunction but is caused when the calculator is exposed to strong electromagnetic noise or static electricity from an external source. Should this occur, press the key and then repeat the calculation from the beginning.

Error conditions:

1. When the integer portion of an answer exceeds 12 digits.
2. When the integer portion of the contents of the memory exceeds 12 digits. (Ex. 9999999999991)
3. When any number is divided by zero. (Ex.5 )

LIMITED WARRANTY

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE, ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability, or otherwise.

In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Your Product

Electronic Calculator

Warranty Period for this Product

Six (6) months pof arts and labor from the date of purchase.

Additional Items Excluded from Warranty Coverage

Any consumable items such as paper, maintenance cartridge, ink cartridges supplied with the Product, or any equipment any hardware, software, firmware, fluorescent lamp, power cords, covers, rubber parts, or peripherals other than the Product.

Where to Obtain Service

At a Sharp Authorized Servicer located in the United States. To find out the location of the nearest Sharp Authorized Servicer, call Sharp toll-free at 1-800-BE-SHARP.

What to do to Obtain Service

Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer. Be sure to have proof of purchase available. If you ship or mail the Product, be sure it is packaged carefully. For your convenience, Genuine Sharp Supplies. Accessories and additional Sharp Products can be purchased from the Authorized Sharp Reseller where you purchased your product, or online at www.sharpplace.com

For More Manuals By Sharp, Visit ManualsLibraryy.

Sharp EL-1801P 2-Digit Serial Printing Calculator-FAQs.