MYW HP65L TV Wall Mount
NOTE: No-load running prohibited!
Before powering on, be sure that the bracket and the TV are installed correctly. Keep the children away from power.
Reset Mode
Disconnect the power supply cord. Wait for 10 seconds and reconnect. Long-press the OK button for 5 seconds until you hear a beep. The mount starts to move upward to the highest position, and the control box emits a double beep
Connect the Mount to a New Device
Short-press the mem2 button five times; you will hear two beeps at the fifth press, which indicates the mount is disconnecting from the current paired device. Then, follow the Guidebook of Tuya App Installation and Operation to connect the mount to a new device
NOTE: If the device fails to search the mount when connecting, follow the above steps or restart the device to re-search the mount.
Coding of Remote Controller and Control Box
- Step 1: When the mount is powered on, press the small button on the control box with a thin tool as shown. The unit emits a beep, indicating that the control box is on standby for program coding.
- Step 2: Press the SET button on the remote control, and the control box repeatedly beeps for approximately 10 seconds, indicating that the remote control is being programmed. The process will be finished automatically until you can‘t hear a beep any longer.
NOTE: Clear up the historical data when replacing a new remote control to pair. Press the small button on the control box with you hear a beep, and hold for 10 seconds to confirm the data-cleaning process is completed until you hear a long beep.
TROUBLESHOOTING
If a problem arises, please try the troubleshooting guidelines below. If the problem is not listed, please contact your local distributor for additional technical assistance.
The motorized TV mount does not respond to the remote control.
Possible reasons are caused by the TV mount or the remote control.
TV MOUNT
- The system may be overheating. Check if the unit beeps four times after pressing the button. If so, allow the unit to cool down and return to room temperature (about 12 minutes).
- The AC/DC end of the power cord may be unplugged/disconnected from the outlet/mount. Check the connection to the outlet/mount to ensure the unit has power
REMOTE CONTROL
- The remote control operating distance may be too far and not in range of the mount. The acceptable range should be less than 10m (30 feet).
- The batteries in the remote control may be low or dead. Replace the batteries.
- The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed. If not, contact your place of Purchase for a replacement.
The TV mount stops moving during operation and emits a long beep.
- Check to see if a foreign object is impeding the mount from moving. If so, remove the object.
- The weight of the TV may exceed the maximum weight limitation of the mounting system.
- The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for a replacement.
The TV mount is making an abnormal noise or sound.
- Check all power connections and reset the system. If the unit continues to make an abnormal noise, please contact your place of Purchase for a replacement.
Hereby, Transmedia Kabelverbindungen GmbH declares that the TV Wall Mount HP 65 L is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.transmedia-germany.com/download
For More Blogs, Visit ManualsLibraryy.
MYW HP65L TV Wall Mount-FAQs
Q1. How does a TV wall mount attach to the TV?
Most mounts use a standard VESA screw-hole pattern with four mounting points on the back of the TV. Screws provided with the mount secure the bracket to the TV.
Q2. What is meant by wall mount setup?
Wall mounting means fixing your TV to the wall instead of placing it on a stand, helping save space and giving a modern look.
Q3. How high should I mount a 65-inch TV?
For the best viewing, the TV’s center should be about 40–42 inches from the floor, which usually places the bottom edge around 24–25 inches above the floor.
Q4. What are common mistakes when mounting a TV?
The biggest mistake is mounting too high, which causes neck strain. Ensure the TV is aligned at eye level when seated.
Q5. Is a 65-inch TV too heavy to mount?
No. Most 65-inch TVs weigh around 50 lbs or less, and the MYW HP65L mount is designed to support them safely if installed properly.
Q6. How do I know if my wall mount will hold my TV?
Check your TV’s weight and VESA size. The mount must support more than your TV’s weight and match its VESA pattern.
Q7. Can I hide cables when wall mounting?
Yes. You can use wall cable raceways or run the cables inside the wall for a clean, clutter-free look.
Q8. What is a VESA pattern?
It’s the standardized distance between the four mounting holes on the back of your TV, measured in millimeters (e.g., 400×400 mm).
Q9. Is it safe to wall mount a 65-inch TV?
Yes, as long as the wall mount is rated for the TV’s size and weight and installed on solid studs or anchors.