Airmoto Tire Inflator Smart Air Pump
Portable Smart Tire Inflater
NOTE: AIR HOSE IS STORED INSIDE THE DEVICE. PRESS THE RELEASE BUTTON ON THE BOTTOM
TUTORIAL: GetAlrmoto.com/HowTo
Packing list
- 1 x smart air pump
- 1 x flexible hose (US standard connector)
- 1 x French standard adapter
- 1 x ball needle
- 1 x nozzle for swimming ring
- 1 x Type-C cable
Specification
- Product name Portable smart air pump
- Product model: BP198
- Product size: 38 x 60 x 152mm
- Weight: 340g
- Inflation pressure: 120PSI (M~)
- No-load flow: 20L/M c
- Charging temperature: O – 45
- Working temperature: -10-60
- Battery capacity: 2000mA/7.2V (14.4WH)
- Charging input: 5V/2A
- USS output: 5V/1.5A
- Charging time 2.5-4.5h
- Pressure accuracy +/- 1 PSI
- LED lighting 0.5W
- Over-current protection: 9A/1S
- Over-discharge protection: 6V
Illustration
ATTENTION:
- Do not leave during inflation
- Keep away from combustible and explosives
- Avoid moisture, sand and fall.
- Do not store the product in a place that is too cold or hot.
- It is forbidden to throw the product into fire or discard it at random due to the built-in lithium battery.
- Not for children
How to use
Charging method
The USS charger is recommended to use 5V / 2A. Use the Type-C charging cable to connect the air pump and power adapter (sold separately) for charging
- Charging s1atus: battery indicator flashes
- Full state: the battery indicator is green and does not flash
- The product cannot be used during charging
Startup and shutdown
*Long press the power button for 3 seconds, as shown in the figure. Switch on successfully
- *Long press the power button for 3 seconds, as shown in the figure Shut down successfully
- *Automatic shutdown in 3 minutes without operation
- *Automatically shut down when the battery is low
Application scenario switching
Short press mode selection key (o) SETTING you can choose 5 inflatable scene modes. They are:
Unit switching
Short press the unit switch key [m], and you can switch the air pressure display unit. The unit conversion formula is shown below 1PSI = 6.89KPA 1BAR = 100KPA 1Kg/cm. = 98KPA
Preset pressure value
Short press +/- button [p]: Adjust the preset pressure value +/- 0.5PSI. Long press +/- button [p]: can quickly adjust the preset pressure value
Note: The scene switch and preset pressure value are automatically saved by the software. You only need to switch the scene for the next use, and the preset pressure is automatically set.
Hose connection
The connection of the hose is shown in the following figure:
Start inflation
Short press the inflation switch [n] to start inflation. The digital display of the real-time air pressure value [f] changes during inflation. Noise will be generated during inflation, and the hose produces high
temperatures during long-term work. Avoid prolonged contact with hose and hose joints by hand [b].
Stop Inflation
- Short press the inflation switch (n) to stop inflation manually.
- When the measured pressure [f] reaches the preset pressure [h] stop inflation automatically.
LED Lighting
- * Long press LED [m] to turn on LED lighting.
- * Press and hold the LED light button [m] to turn off the LED light.
Hose storage
The hose can be stored in the storage hole as the following figure shows, just put the thread head of the hose inside the hole to store it.
Measuring pressure
After switching on, connect the air pipe to the measured object, and the measured pressure value [f] shows the current pressure value.
Air release valve
Connect the air pipe to the measured object and press the air release valve [a] to deflate.
Clearing the pressure
After switching on, when the measured pressure value is not zero, press the preset +/- key [m] for 3 seconds at the same time to enter auto clear.
Note:
The product has been cleared from the factory. When the difference in altitude or the sensor tolerance shows that the measured pressure is not zero, manual clearing can improve the accuracy of pressure detection. Do not connect inflatable objects when clearing.
High-temperature safety precautions
When the hose is unscrewed, the air pipe and the joint will generate high temperatures due to long-term work. Do not touch it with your hands for a long time.
Common product pressure values
For more manuals by Airmoto, visit ManualsLibraryy
Airmoto Tire Inflator Smart Air Pump-FAQs
How long does it take to charge an Airmoto?
The Airmoto takes between 2-3 hours to fully charge and can hold that charge for up to 40 minutes of continuous use.
Can I use the Airmoto in a car without the engine running?
Yes, but ensure the ignition is in the “accessories” or “on” position to power the DC plug, and follow safety precautions.
How long do air pump batteries last?
The Airmoto’s battery can last up to 40 hours under continuous output mode and up to 120 hours in intermittent mode.
What are the key features of the Airmoto?
The Airmoto is a portable tire inflator with a rechargeable 2000 mAh battery, auto shut-off, and maximum pressure of up to 120 PSI.
How long does a tire inflator typically last?
The lifespan of a tire inflator varies, but a well-maintained one can last several years if manufacturer guidelines are followed.
Why is my tire inflator not inflating?
Check for blockages in the system, such as a clogged air filter, which can hinder air intake and reduce output.
How does a tire inflator work?
A tire inflator converts electric energy into potential energy, storing it as pressurized air, which is then used to inflate tires.
Does the Airmoto have an auto shut-off feature?
Yes, the Airmoto has an auto shut-off feature to prevent over-inflation.
Can I run the air pump 24/7?
It’s generally recommended to leave the air pump on continuously to provide good water circulation and oxygen for fish.
Can air pumps overheat?
Yes, air compressors can overheat due to internal or external factors, but they should quickly cool down after use.