Fisher-Price V0206 Baby Jumper User Manual

Fisher-Price V0206 Baby Jumper

WARNING

To prevent serious injury or death:

• Use only for a child who can hold their head upright unassisted and who is not able
  to walk or climb out of the product.
• Never leave a child unattended. Always keep the child in view while in the product.
• Never use near steps, pools, hot surfaces, or areas that may be hazardous to a child.
  The product may move during use.
• To avoid tip-over, place the product on a flat, level surface.
• Strings can cause strangulation! DO NOT place items with a string around a child’s
  neck, such as hood strings or pacifier cords. DO NOT suspend strings over the product or attach strings to toys.

Consumer Information

IMPORTANT! PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

• Please read these instructions before assembly and use of this product.
• Adult assembly is required. Tool needed for battery installation: Phillips screwdriver (not included).
• Requires three “AA” (LR6) alkaline batteries (not included) for electronic toy operation.
• Use only for a child:
  • – who can hold their head up unassisted
  • – who is not able to climb out
  • – who weighs less than 25 lbs. (11,3 kg) and is less than 32 inches (81 cm) in height.
• Product features and decorations may vary from photos.

Parts

Electronic Toy

Elephant Toy

Spinning Ball

2 Hanging Toys

Frame

Spinning Disc

Pad

Seat

3 Bases

Assembly

IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts, or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.

• Insert and “snap” the elephant toy, spinning disc, electronic toy, and spinning ball into the slots on the seat ring.

• Place the bases on a flat surface.
• While pressing the button on the short tube of a base, insert it into the long tube on another base. Continue to slide the short tube into the long tube until you hear a “click”.
• Repeat this procedure to assemble the remaining base to the base assembly

• Position the seat so that the inside (ribbed side) is up and the star marking is toward you.
• Fit the yellow slots on the pad to the seat pegs on either side of the star marking.

• Pull the pad through the seat. Wrap the edges of the pad around the outside of the seat.

• While pressing the button on a frame tube, insert it into a base tube. Continue to slide the frame tube into the base tube until you hear a “click”. Pull up on the frame tube to be sure it is secure.
• Repeat this procedure to assemble the two remaining frame tubes to the base tubes.

• Fit the other six button holes in the seat pad onto the corresponding pegs on the seat.

• Fit the hanging toys into the slots on the frame tubes.
• Push to “snap” the toys in place.

• Insert and “snap” the seat with the pad into the seat ring. Pull up on the seat to be sure it is secure.

Battery Installation

• Loosen the screws in the battery compartment door with a Phillips screwdriver and remove the battery compartment door.
• Insert three “AA” (LR6) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and then back on.
• When sounds or lights become faint or do not work at all, it’s time for an adult to replace batteries.

Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Set Up and Use

Seat Height Adjustment

1. Place your child in the seat. Check the distance between your baby’s feet and the floor. Your child’s toes should touch the floor (without bouncing). If your child’s entire foot is touching the floor or the toes are not touching the floor at all, adjust the height to any of three positions (one for the smallest child and three for the
   tallest child).
2. Remove your child from the seat.
   • Lift the seat ring so the bottom faces you.
   • Locate the strap bar and pull it open.
     
3. Pull the strap to the desired height.
4. Fit the strap bar into the desired slot in the strap
5. Push to “snap” and fasten the strap bar. Repeat this process to attach the other two straps to the seat ring

Jumpin’ Fun!

• Slide the power/volume switch to:
  • On with low volume
  • On with high volume
  • Off
• Slide the mode select switch to short play or long play.
• Short Play – Baby’s jumping activates lights and music.
• Long Play – Mom can choose this mode to play up to
• 5 minutes of continuous music.

Care

• The seat pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly.
• The frame, seat, seat ring, straps, and toys may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove soap residue. Do not immerse the electronic toy.

Remove the Seat and Pad

• Lift the seat ring. While pressing near any notch on the seat, pull the seat from the seat ring. Turn the seat over. Remove the pad slots from the pegs on the seat. Remove the pad.

Replace the Seat and Pad

• Please follow the Assembly instructions.

FOR MORE MANUALS BY Fisher-Price, VISIT MANUALSLIBRARYY

Fisher-Price V0206 Baby Jumper-FAQs