NutriBullet ZNBF30500Z Blender Combo User Manual

NutriBullet ZNBF30500Z Blender Combo

What’s included

Assembly guide

Getting started

PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE APPLIANCE:

Make sure the base is plugged in for use.
DO NOT attempt to operate the pitcher on the appliance without attaching the pitcher lid and vented lid cap.
Never run the appliance while empty.
Appliance accessories are not intended to be used in the microwave, as they may damage the microwave.
Never leave the appliance unattended while in use.

Never blend hot liquids when using any sealed NutriBullet® cups.

WARNING

Heated ingredients can pressurize sealed containers when agitated and violently expel hot contents upon opening. Always start the blending process with room temperature or refrigerated ingredients and liquids (21°C/70°F or cooler).

Use extra caution when blending hot liquids in the pitcher.

Steam and splatters can escape through the vented lid, potentially causing scalding and/or burns. NEVER blend hot liquids in your pitcher without the pitcher lid and vented lid cap attached. The vented lid cap is ventilated to allow steam and pressure to release, while guarding against excess splashing. NEVER blend hot liquids in your Nutribullet cups or any other sealed vessel.

When blending hot liquids, add liquid and solid ingredients to your pitcher below their respective MAX lines. Attach the pitcher lid with the vented lid cap inserted. Press the POWER icon, then begin blending on the LOW setting. Once ingredients are integrated and the mixture is level (no splashing), increase speed as needed.

Pitcher assembly & use

Review all warning and caution statements in the Important Safeguards section (pg 3-9) and on the previous page before proceeding to Step 2.
Place the motor base on a clean, dry, level surface such as a counter or table.
Place the pitcher onto the motor base — handle facing to the right of the blending control panel, never towards the back — and gently twist clockwise so it locks in place. When you hear the click, it’s locked and ready to blend.
NOTE: If you are left-handed, place the handle facing towards the center of the blending control panel and twist clockwise.
Add the ingredients to the pitcher, making sure they do not exceed the MAX line.
NOTE: The blending pitcher is marked with two MAX lines: one for solid ingredients (higher line) and one for liquids (lower line). When filling the blender, make sure your ingredients do not exceed their respective MAX lines.
Place the pitcher lid with the vented lid cap attached on the pitcher, making sure it’s aligned with the handle.
Plug the power cord into an electrical outlet and press POWER to turn on the blender.
To start blending, select a speed or the EXTRACT program on the blending control panel. This program will turn off automatically. Buttons will illuminate while in use.
NOTE: Proceed to the blending control panel chart on page 20 for speed definitions.
NOTE: If you need to add additional ingredients while blending, switch the setting to LOW and remove the vented lid cap from your pitcher lid, leaving the lid attached. Add ingredients through the hole in the top of the lid, followed by the tamper if necessary. Replace the vented lid cap, then increase to your desired speed.
DO NOT attempt to add items through the vent hole when blending hot ingredients.CAUTION: Do not use any apparatus other than the tamper to push ingredients toward the blade. The tamper is specifically designed not to come in contact with the blade. Spatulas, spoons, and other tools are long enough to reach the blade, which may result in damage to the machine, damage to property, and possible injury.
If the ingredients stick to the side of the pitcher, stop the appliance by pressing POWER and wait for the blade to stop turning. Then remove the pitcher lid and use the tamper to dislodge the ingredients. When finished, replace the lid and continue blending. If the ingredients continue to stick, consider adding a little more liquid.
When you have reached your desired consistency, pause/stop the appliance by pressing POWER or the speed you selected and wait for the blades to stop turning. The unit will enter idle mode. The POWER button will remain illuminated.
WARNING: Blades are sharp. Never insert your hands into the pitcher.
Press POWER to turn off the unit completely.
Twist the pitcher counterclockwise and lift off the motor base. Pour and enjoy!

NutriBullet® cup assembly & use.

Review all warning and caution statements in the Important Safeguards section (pg 3-9) before proceeding to Step 2.
Place the motor base on a clean, dry, level surface such as a counter or table.
Add ingredients to the NutriBullet® cup.
NOTE: Do not overfill! To avoid leakage, do not add ingredients beyond the MAX line.
Twist the easy-twist extractor blade onto the cup until tightly sealed.Handle the easy-twist extractor blade assembly with care, as the blades are sharp. Never leave the appliance unattended while in use.
NEVER BLEND HOT LIQUIDS,
as doing so may cause excessive pressure buildup, resulting in the risk of personal injury and or property damage.
Plug the power cord into an electrical outlet and press POWER to turn on the blender.
Turn the cup upside down and place it onto the motor base, gently turning the cup clockwise to lock it into the motor base.
To start blending, select a speed or the EXTRACT program on the blending control panel. This program will turn off automatically. Buttons will illuminate while in use.
NOTE: Proceed to the blending control panel chart on page 20 for speed definitions.
When you have reached your desired consistency, pause/stop the appliance by pressing POWER or the speed you selected and wait for the blades to stop turning. The unit will enter idle mode. The POWER button will remain illuminated.
NOTE: speeds will automatically shut off after 60 seconds.
Press POWER to turn off the unit completely.
Unlock the assembly by gently twisting the cup counterclockwise. You will hear a click. Enjoy!
NOTE: Blending should never take longer than one minute to yield smooth and creamy results.

CAUTION

Do not remove the easy-twist extractor blade from the NutriBullet® cup until blending has completely ceased. Do not use the easy-twist extractor blade as a storage lid for your cup. Some foods may contain active ingredients or release gases that will expand if left in a sealed container, resulting in excessive pressure buildup that can pose a risk of injury. When storing contents in the cup, use plastic wrap or foil to seal your container. Always point the contents away from your body when unsealing.

Blending control panel

TURNING ON/OFF

The power button activates the master power of the appliance. When pressed, this button lights up to indicate the motor is powered on, and the other functions can be used. Always turn the master power off and unplug the unit when the machine is not in use.

THE EXTRACT PROGRAM

Use to break down whole fruits, vegetables, and ice into nutrient-rich smoothies. This button will activate a run cycle that shuts off automatically.

LOW SPEED

Use to mix thin batter, gravies, marinades; scramble eggs; process cooked foods and uncooked fruits.

MEDIUM SPEED

Use to cream soups, mix dips, grind nuts, and blend sauces, spreads, mixed drinks, powdered drinks, and milkshakes.

WARNING!

NEVER BLEND HOT LIQUIDS IN ANY SEALED NUTRIBULLET® CUP. Doing so may cause excessive pressure buildup, resulting in the risk of personal injury or property damage. Hot items should only be blended in the pitcher using proper safeguards.

HIGH SPEED

Use to liquefy thick mixtures and blend frozen fruits and vegetables.

PULSE*

Use to control chopping and processing.

WARNING: DO NOT use this setting with hot ingredients!

How to use the blending control panel.

LOW, MEDIUM, OR HIGH

Select a speed and press once to turn on. The button will illuminate. To pause/stop the unit, press the button a second time — it will de-illuminate — or press POWER. While in the idle mode, the POWER button will remain lit. To fully power down after pausing, press POWER and unplug the unit.

NOTE: If using the pitcher, speeds will run until paused/stopped. If using the NutriBullet® cups, speeds will automatically shut off after 60 seconds.

THE EXTRACT PROGRAM

Press the EXTRACT button and the NutriBullet® Blender Combo will do the work for you. This program automatically stops at the end of its cycle. To pause or stop the blender, press EXTRACT again or POWER .

PULSE

Press and release the PULSE button to chop ingredients. If you hold this button down, it will continue to run until you release it.

Care & maintenance

Cleaning the NutriBullet® is easy. The pitcher is dishwasher-safe, while the cups and to-go lids are TOP RACK dishwasher-safe. The easytwist extractor blade and motor base can be quickly hand-washed with soap and water. Read on for best practices.

Here’s how to clean the NutriBullet®:

STEP 1

The most important thing — ALWAYS POWER OFF THE UNIT and UNPLUG the motor base from the power outlet when it is not in use. Do not attempt to handle the appliance until all parts have stopped moving! This includes during assembly and disassembly, while changing accessories during cleaning, and any time you leave the machine unattended.

STEP 2

Detach the NutriBullet® cup / easy-twist extractor blade or pitcher from the motor base.

STEP 3

Clean the individual components (motor base, easy-twist extractor blade, NutriBullet® cups) as recommended in the following pages.

MOTOR BASE

To avoid the risk of injury, NEVER attempt to clean the actuator system on the motor base while the NutriBullet® Blender Combo is plugged in.
Do not attempt to remove any pieces from the motor base.
Use a sponge or dishcloth dampened with warm, soapy water to wipe down the motor base until clean.
If necessary, you may use a small brush to scrub the actuator system area to ensure it’s clean.
To clean leakage residue from the motor base, wipe with a damp sponge and warm water.
If necessary, you may use a small brush to scrub the actuator system area to ensure it’s clean.

WARNING: Never submerge the motor base in water.

EASY-TWIST EXTRACTOR BLADE

Blades are sharp! Handle the easy-twist extractor blade with care when cleaning! It is best to clean blades immediately after use to reduce the buildup of residue. If food particles get stuck, use a small brush or sponge to target and dislodge them.
Do not remove any components of the easytwist extractor blade; this can result in permanent damage to the blade, resulting in leakage when blending. If, over time, the easy twist extractor blade becomes loose or damaged, you may order a new easy twist extractor blade at nutribullet.com or contact customer service.
Dry the easy-twist extractor blade completely after every use.
Regularly check the condition of the bottom of the blade for cracking or breakage. If damaged, replace the easy-twist extractor blade immediately to prevent possible personal injury.

NUTRIBULLET® CUPS & TO-GO LIDS

These items are TOP RACK dishwasher-safe. We recommend rinsing and briefly scrubbing them with a dish brush to remove any remaining debris before placing them in the dishwasher. NEVER use the sanitize cycle to wash the cups — heating this high can warp the plastic.

NUTRIBULLET® PITCHER

WARNING: Blades are sharp! Use caution when cleaning the pitcher.

The pitcher is dishwasher-safe. We recommend rinsing and briefly scrubbing it with a dish brush to remove any remaining debris before placing it in the dishwasher.
NEVER use the sanitize cycle to wash the pitcher — heating this high can warp the plastic.
If preferred, hand-wash the pitcher with soap and water. Stuck-on ingredients might require extra scrubbing with a dish brush or sponge.
Regularly check the structure of the pitcher and twisting threads for cracking, crazing, or breakage. If damaged, replace immediately to prevent possible personal injury.
NEVER USE A PITCHER THAT DOES NOT PROPERLY ALIGN WITH THE BLADE.
Doing so may cause the pitcher and motor base to separate, exposing the blade assembly and potentially causing severe personal injury.

TAMPER

Always hand-wash the tamper with soap and water. Stuck-on ingredients might require extra scrubbing with a dish brush or sponge.

STUBBORN CLEAN UP

If ingredients get stuck to the NutriBullet® cups, easy-twist extractor blades, or pitcher, here’s an easy cleanup solution: fill the vessel with room temperature (21°C/70°F or less) water to its MAX line and add 1-2 drops of dish soap. For cups, twist on the easy-twist extractor blade, and blend on the motor base for 20-30 seconds. For the pitcher, attach the lid and blend on the motor base for the same amount of time, 20-30 seconds. This should loosen debris enough to scrub away with soap and water.

How to store

Store the NutriBullet® Blender Combo pitcher upright with the pitcher lid secured on top. Do not place anything on top of the pitcher lid. Store remaining pieces in a safe place where they will not be damaged and won’t cause harm.

WARNING: NEVER store the easytwist extractor blade on the motor base without a NutriBullet® cup or the pitcher, as the exposed blades pose a serious laceration hazard.

Replacement parts.

To order additional parts and accessories, please visit our website at nutribullet.com/shop/accessories or feel free to contact customer service: 1.800.523.5993.

Nutribullet® Blender Combo one-year limited warranty

LIMITED WARRANTY FOR NUTRIBULLET®

NutriBullet’s limited warranty obligations are confined to the terms set forth below:

NutriBullet, LLC (“NutriBullet”) warrants this NutriBullet® against defects in materials and workmanship for one year from the date of original retail purchase. This limited warranty is valid only in the country in which the product is purchased and comes with the product at no extra charge, however, shipping and processing fees will be incurred for returns, replacements, and or refunds.

If a defect exists, and NutriBullet® is obligated under this limited warranty, at its option NutriBullet® will (1) repair the product at no charge, using new or refurbished replacement parts, (2) exchange the product with a product that is new or that has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (3) refund the purchase price of the product. A replacement product assumes the remaining warranty of the original product. A repaired product has a one-year warranty from the date of repair. When a product or part is exchanged, any replacement item becomes your property, and the replaced item becomes NutriBullet’s property. When a refund is given, your product becomes NutriBullet’s property.

OBTAINING WARRANTY SERVICE

For limited warranty service, simply call our customer service department at 1 800- 523 5993 or contact us via email from our website at nutribullet.com, simply click the contact us link, fill out and submit the customer contact form, and we will be glad to help you. When you contact our customer service department, you will be asked for your name, address, telephone number, and to provide proof of the original purchase (receipt) containing a description of the products, purchase date, and the appropriate NutriBullet® serial number(s). Before you send your product for limited warranty service, please make sure to keep a copy of all relevant documents for your files (receipt, etc.). It is always recommended to purchase product insurance and tracking services when sending your product for service. Remember, shipping and processing fees will be incurred and are not covered by the one-year limited warranty.

EXCLUSIONS & LIMITATIONS

This NutriBullet® One-Year Limited Warranty applies only to NutriBullet® products distributed by or for NutriBullet® that can be identified by the “NutriBullet” trademark, trade name, logo, and bar code. NutriBullet® Blender Combo’s One-Year Limited Warranty does not apply to any other products that may appear to be authentic, but were not distributed/sold by NutriBullet, LLC.

Normal wear and tear is not covered by this limited warranty.

This limited warranty applies to consumer use only and is void when the product is used in a commercial or institutional setting.

This limited warranty extends only to the original consumer purchaser and is not transferable. In addition, proof of purchase must be demonstrated.

Repair or replacement of the product (or, if repair or replacement is not feasible, a refund of the purchase price) is the exclusive remedy of the consumer under this limited warranty. NutriBullet, LLC shall not be liable for any incidental or consequential damages for breach of this limited warranty or any implied warranty on this product.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. NutriBullet® is not liable for any damage to products not covered by this warranty (e.g., cups, book, User Guide).

This limited warranty does not apply:

to damage caused by accident, abuse, misuse, or misapplication;
to damage caused by improper maintenance (including unauthorized parts service);
to a product or a part that has been modified in any way;
If any NutriBullet® serial number or trademark has been removed or defaced; or
If the product has been used with an adapter/converter.

THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND INSTEAD OF ALL OTHER WARRANTIES, REMEDIES, AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. NUTRIBULLET® SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF NUTRIBULLET CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY.

No NutriBullet® reseller, agent, or employee is authorized to make any modification to this warranty.

NUTRIBULLET IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL, AL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY. NUTRIBULLET® SPECIFICALLY DOES NOT REPRESENT THAT IT WILL BE ABLE TO REPAIR ANY PRODUCT UNDER THIS LIMITED WARRANTY.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitations on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary by state or province.

Warranty registration

Please visit nutribullet.com/shop/accessories or call 1.800.523.5993 to register your new NutriBullet® Blender Combo. You will be asked to enter the Serial Number* of your product, along with the purchase date and place of purchase.

The registration will enable us to contact you in the unlikely event of a product safety notification. By registering your product, you acknowledge having read and understood the instructions and warnings set out in the accompanying instructions.

For more manuals by NutriBullet, visit ManualsLibraryy

Blog Post