Bellini BDG302WG 2 Burner Gas Glass Cooktop Manual

Bellini BDG302WG 2 Burner Gas Glass Cooktop

Product Description

Technical Specifications

NOTE: On completion of the installation of the cooktop to the kitchen bench, the distance from the benchtop surface to the highest part of any trivet is 55.5 mm, as shown in the illustrations.

Installation

Before Installation:

• Before cutting into any benchtops, ensure the minimum clearances to walls, adjacent surfaces, and overhead surfaces required by the relevant gas appliance installation code (see above) will comply. Dimensions are specified in millimeters (mm).
• Overhead cupboards and range hood = 650 mm.
• Side and rear clearance = 200 mm to any burner edge.
• Overhead exhaust/ceiling fan = 750 mm.
• Horizontal surfaces adjacent to the hob = less than or equal to the hob height.
• Ensure there is sufficient clearance to fit the regulator and/or flexible hose connection with the hotplate in the installed position.
• Where a range appliance or rangehood is replaced, the overhead clearance from the highest part of the highest burner of the appliance (or hob) to the rangehood shall not be less than 600 mm unless the appliance manufacturer’s instructions specify a greater clearance.

When you have installed the hob, make sure that:

• The GPO (general purpose outlet) must always be in an accessible position.
• The supply connection point, test point, and natural gas regulator adjustment screw (for Natural gas installation) are accessible for testing and/or adjustment with the hotplate in the installed position.

1. Cupboard Cutting

Bench top thickness, 30–40 mm (3–4 cm).

2. Place Burner Box

Apply the adhesive sealing tape to the underside lip of the burner box, shown at G opposite. Place the burner box into the cutout hole and fit the clamping brackets to clamp the hotplate to the bench.

Installation of clips:

1. Put the clip inside the edge of the hole (image 1).
2. Fix the installation bracket with a screw (image 2).

3. Fit Burners And Trivet

• Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). The ignitor (S) must be clean for trouble-free sparking. Test burner ignition and burner flame for correct operation. If the burner is placed correctly, it will not rotate on its supports.
• The Triple Ring (Wok) burner (diagrams below) does not fit over the igniter or thermocouple but must be placed on its supports. Make sure the trivet is fitted onto its locator on burners and can’t rotate after assembly.

4. Electrical Connection

Install a 10 amp general purpose outlet (GPO) in accordance with relevant electrical standards and/or codes of practice applicable. The power supply cord (supplied) must not touch any hot surfaces and must be placed so that its temperature does not exceed 75°C at any point along its length. After having installed the hotplate, the GPO must always be in an accessible position.

5. Gas Connection

Install in accordance with the relevant gas standards and/or codes of practice applicable. Connect the elbow fitting to the appliance gas manifold connection, and check that seals between the elbow and manifold connection are in place and in good condition.

• For Natural gas: connect the natural gas appliance regulator (pictured opposite) with integral test point using approved gas thread tape or compound to the elbow fitting.
• For Universal LPG: connect the brass test point adaptor (pictured opposite) using approved gas thread tape or compound to the elbow fitting.
• Ensure the supply connection point, test point, and natural gas regulator adjustment screw (for Natural gas installation) are accessible for testing and/or adjustment with the hotplate in the installed position.
• Where a flexible hose assembly is used, ensure it is approved to AS/NZS 1869, Class B. Any hose assembly used must be restrained from accidental contact with the flue outlet of an under-bench oven. This hose assembly shall be suitable for connection to a fixed consumer piping outlet located as follows:
• Hotplates at a point 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm.
• After connecting to gas, check for leaks using a soapy solution, never a naked flame.
• Fit the duplicate data plate (supplied in a separate bag) on a surface adjacent to the hotplate, for example, the inside of the cupboard door, so it is clearly visible for any service technician.

SETTING THE GAS PRESSURE:

• Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas).
• For the Model BG604G(-F), light the Triple Ring and Auxiliary burner and adjust the test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck that the pressure is the same as set previously or adjust as required.
• For all the other models, light all burners and adjust the test point pressure to 1.00 kPa. Turn burners off and on again, and recheck that the pressure is the same as set previously or adjust as required.

TEST FOR CORRECT OPERATION:

After installation and adjusting burner pressure using the test point, each burner ignition and operation must be tested individually and with all burners operating. This testing must be done by the installer before leaving.

ADJUSTING THE BURNER MINIMUM FLAME HEIGHT:

NOTE: This adjustment can only be performed by the installer or authorized service personnel.

The minimum burner flame is factory adjusted for the gas type stated on the gas type label adjacent to the gas connection and should not require adjustment. Adjustment may be required if the hotplate has been converted from Natural gas to Universal LPG or vice versa.

GAS CONVERSION INSTRUCTIONS:

The manufacturer’s servicing instructions detail how authorized personnel may convert the hotplate from Natural gas to Universal LPG or from Universal LPG to Natural gas. Contact the manufacturer or agent as required.

Start Using Your Appliance

• The hotplates are fitted with mains-powered electronic spark ignitors, so they must be connected to the mains power supply (i.e., nominal 230 V ac) to operate. If power is not available, the hotplate will still work, but the burners will have to be lit with a match or similar.
• Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit while at the same time depressing the gas control knob to activate the spark ignition.
• Once the burner is alight, continue to depress the gas control knob for 5–10 seconds to allow the flame safeguard to activate. If, when you release the gas control knob, the burner flame goes out, the flame safeguard has not heated up enough, so repeat the ignition procedure after waiting 1 minute for the gas to disperse. If
• problems with burner lighting persist, refer to the TROUBLESHOOTING section of these instructions.
• If power is not available, light a match or similar, then turn the gas control knob for the burner to be lit to the High Flame setting. Once again, if problems with burner lighting persist, refer to the TROUBLESHOOTING section of these instructions.
• When the burner lights, adjust the desired flame height. On finishing, turn the control knob to the off position marked with a black DOT.

Maintenance & Troubleshooting

Warning:

To maintain safe operation, it is highly recommended that this appliance be inspected and serviced every two years by an authorized service person. Cleaning and maintenance should be carried out with the appliance cold, especially when cleaning the enameled parts. Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the surfaces.

STAINLESS STEEL

The stainless steel hob of the hotplate must be cleaned regularly (e.g., weekly) to ensure a long life expectancy of the hotplate. Ensure the hotplate has cooled. Wash down with warm, soapy water and rinse with clean water. Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.

NOTE: Ensure that wiping is done along the grain of the stainless steel to prevent any unsightly crisscross scratching patterns from appearing.

TRIVETS (UTENSIL SUPPORTS)

Enameled parts must only be washed with a sponge and soapy water or with non-abrasive products. Rinse with clean water. Dry with a clean soft cloth.

BURNERS

• Remove trivets from the hob. Ensure burners are cool. Remove the burners’ enameled cap (C) and aluminum burner crown (F).
• Wash down with warm, soapy water and rinse with clean water. Dry with a clean soft cloth. Use a cotton bud, toothbrush, or some other item to clean out any incrustations or dirt from the four holes marked (H).
• Replace burners and ensure they are correctly repositioned over the igniter (S) and thermocouple (T).
• The igniter (S) must be clean for trouble-free sparking. Test burner ignition and burner flame for correct operation. The Triple Ring (Wok) burner (diagrams below) does not fit over the igniter or thermocouple but must be placed on its supports. If the burner is placed correctly, it will not rotate on its supports.

TROUBLESHOOTING

Servicing of the hotplates must only be done by an authorized service representative (see back of this booklet), and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted.
It is recommended that the hotplate be serviced by an authorized person at least every 2 years. This service is not covered by warranty.

Abnormal conditions include:

• Excessively yellow or sooting flame type.
• Flame lifting off the burner ports.
• Flame lighting back into the burner (normally associated with a popping sound).
• Objectionable odor of the flame’s combustion products.
• Should a faulty condition develop in the hotplate that is not described above, refer to the following table first for possible causes and remedies before contacting an authorized service representative. Servicing beyond the remedies listed shall only be undertaken by an authorized service representative.

WARRANTY

• In this warranty:
• Australian Consumer Law means the law as set out in Schedule 2 of the Competition and Consumer Act 2010;
•  Company means GSM Retail Australia Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose Park, SA 5067. Telephone 1300 373 199. Email [email protected].
• Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer Law as the original purchaser of a Bellini product;
• Consumer Guarantees means the guarantees under the Australian Consumer Law;
• You means the Consumer.
• Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to any Consumer under this warranty are in addition to the rights and remedies available under any Consumer Guarantees.
• Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini product will be free of manufacturing defects and will perform to the Company’s specifications.
• The benefit of this warranty extends only to the Consumer as the original purchaser of a Bellini product, which is installed in a domestic household area.
• The in-home warranty does not apply to Commercial and/or industrial usage. *Please see 1.7.7 for additional information.
• This warranty commences on the date of purchase of the Bellini product by the Consumer and continues for the benefit only of the Consumer until the expiry of three (3) years (Warranty Period).
• If, within the Warranty Period, a manufacturing defect is discovered in the Bellini product or it fails to perform to the Company’s specifications as a result of some defect in materials, components, or workmanship (Defect), then the Company will, at its option, repair the Bellini product or supply a replacement Bellini product free of charge. A replacement Bellini product may differ from the original product purchased by the Consumer.
• This warranty will not apply to any Bellini product:
• Installed by any person other than a qualified tradesperson; or
• Subjected to misuse, neglect, negligence, or accidental damage; or
• Operated in any way contrary to any operating or maintenance instructions; or
• Improperly handled, installed, or maintained; or
• Altered or modified before or after installation; or
• Damaged directly or indirectly by power surges, electrical storm damage, or connection to an incorrect power supply;
• Industrial and/or Commercial usage is inclusive of staff areas in office/shop environments, hotel/motel or other similar accommodation or rental type properties, including Bed and Breakfast establishments.
• You must provide proof of your purchase of the Bellini product and the date of purchase to obtain the benefit of this warranty.
• If you live outside the service area of the Company or one of its service agents, this warranty does not cover the cost of transport of the Bellini product for service, nor the service agent’s traveling costs to and from your home.
• If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is safely disconnected by a qualified tradesman and securely packed and insured. The Company does not accept any responsibility for loss or damage to the Bellini product prior to it being received by the Company or its service agent.
• You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the Bellini product by the Company (whether it is the original or a repaired and/or replacement Bellini product) and for any other expenses you incur in claiming under this warranty.
• The Company or its service agent will examine any Bellini product and, if the Company determines that it is defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the Bellini product in accordance with this warranty.

DO NOT SEND IN THIS WARRANTY

Fill out the following details and file with your purchase invoice for safekeeping.

RETAIN & FILE WITH YOUR RECEIPT

Your Purchase Receipt/Invoice is proof of the date of purchase. If you are unable to establish the date of purchase, or if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required to bear all service call charges. GSM Retail Australia Pty Ltd reserves the right to discontinue items, modify designs, and change specifications without incurring obligation. Whilst every effort is made to ensure that descriptions, specifications, and other information in this publication are correct, no warranty is given in respect thereof, and the company shall not be liable for any errors therein.

• Purchased from:
• Co. Name:
• Address:
• Date of Purchase:
• Serial number:

NOTE: Consistent with our continuing product development policy, improvements may have been made that render the contents of this packaging slightly different from those shown. For Warranty and technical queries: New Zealand 0800 764 912 www.belliniappliances.com.au.

For More Manuals By Bellini, Visit ManualsLibraryy.

Bellini BDG302WG 2 Burner Gas Glass Cooktop-FAQs