GermGuardian AC3000 Airsafe+ Intelligent Air Purifier User Manual

GermGuardian AC3000 Airsafe+ Intelligent Air Purifier

READ AND SAVE THESE INSTRUCTIONS

• IMPORTANT – This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• WARNING: To reduce the risk of fire or electric shock do not use with an extension cord.
• To avoid fire or shock hazards, plug the appliance directly into a 120V AC electrical outlet.
• Keep the cord out of heavy traffic areas. To avoid fire hazards, NEVER put the cord under rugs, near heat registers, radiators, stoves or heaters.
• To protect against electrical hazards, DO NOT immerse in water or other liquids. Do not use near water.
• Extreme caution is necessary when any appliance is used by or near children or people with disabilities and whenever the appliance is left operating unattended.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do NOT play with the appliance.
• Always unplug the air purifier before moving it, opening the grill, changing filters, cleaning,  or whenever the air purifier is not in use. Be sure to pull by the plug and not the cord.
• NEVER drop or insert any object into any openings.
• DO NOT run a cord under the carpeting.
• DO NOT cover the cord with throw rugs, runners, or similar coverings.
• DO NOT route the cord under furniture or appliances. Arrange the cord away from the traffic area and where it will not be trimmed over

SPECIFICATIONS

Intelligent Air Purifier + HEPA + UVC

Control Panel

AIR CLEANING SYSTEM

• Improve your indoor air quality with your new Germguardian Air Purifier. The HEPA filter captures allergens and includes a charcoal filter layer to help reduce household odors. The UV-C light helps to reduce airborne germs

OPERATING INSTRUCTIONS

BEFORE OPERATING THE AIR PURIFIER

1. Select a firm, level, and flat location for the air purifier.
   • For proper airflow, locate the unit at least 1 foot from any wall or furniture.
   • Make sure none of the grills are blocked.
2. Plug the power cord into a 120V AC outlet.

OPERATING THE AIR PURIFIER

1. Power Button Operation – Press the power button:
   • ONCE, turn the unit on and put it into auto mode. The Auto Mode indicator on the control panel will turn on.
   • TWICE to enter speed one. The low fan speed indicator on the control panel will turn on.
   • THREE times to enter speed two. The medium fan speed indicator on the control panel will turn on.
   • FOUR times to enter speed three. The high fan speed indicator on the control panel will turn on.
   • FIVE times to enter sleep mode. The air quality monitor on the front of the unit will flash for 10 seconds, all lights will turn off, and the air purifier will run at a low fan speed.
   • SIX times to power the unit off.
2. UV-C – Press the UV-C button to turn on the UV-C light. When the UV-C light is on the button will illuminate. To turn off the UV-C. Press the button again.

What is Auto Mode?

• When in auto mode the fan speed will change depending on the air quality level in the room. If the AQM detects higher particle levels, the air purifier will kick into a higher fan speed. After the air quality has improved, the speed will be lower. You can leave the air purifier in auto mode 24/7 for best results. To exit auto mode press the power button again to cycle through the remaining speed levels.
• What is Sleep Mode?
• In sleep mode, the air purifier will run at Speed One with no lights while still filtering the air. To exit sleep mode, press the power button again and the unit will shut off

AIR QUALITY MONITOR

• Air Quality Monitor senses and detects the amount of particulate matter (PM2.5) in the air. The light on the front of the unit will change colors, indicating the air quality level in the room. See values and status ranges in the chart below. Also listed are the color values displayed on the AQM and the fan speed “AUTO” mode will be selected based on the particulate matter that is detected
  

  Light Color	Particulate Matter Value (Range)	Air Quality Status	Auto Fan Speed
  Green	0-100	Good	1
  Yellow	101-200	Average	2
  Red	201-500	Poor	3

FILTER CLEANING AND MAINTENANCE

WHEN TO REPLACE THE FILTER

• Depending on usage and environmental conditions the filter will last approximately 6 months. The filter replacement indicator light on the control panel will flash red when it is time to replace the filter. The filter will also turn from white to grey when it is dirty and needs replacing. Replace the filter according to the directions then press the power button and hold for 3 seconds to reset the light.
• IMPORTANT: DO NOT wash and re-use the filter. Please contact Customer Service or visit our website guardiantechnologies.com to purchase a replacement filter.

REMOVING AND REPLACE FILTER

1. Turn off and unplug the unit.
2. Remove the bottom panel by pressing the two corners and pulling up.
3. Replace with new filter – pushing completely into the unit.
4. Return the bottom panel and ensure all three corners are locked in place when you hear the dick.
   • IMPORTANT: Make sure the filter is installed and the bottom panel is closed properly, otherwise, the unit will not function. RESET THE FILTER LIGHT by holding the Power Button control for 3 seconds.

INSTALLING & REMOVING UV-C BULB

• The UV-C light will begin to flash continuously when it’s time to replace the UV-C bulb. Replace the bulb according to the directions then press the UV-C control button and hold for 3 seconds to reset the UV-C indicator light.

CHANGING THE UV-C BULB

1. The UV-C bulb is located in a compartment in the center of the purifier. To access, first follow the instructions to remove the filter.
2. After removing the filter, hold the unit in place with one hand. Locate the bulb cover and turn in a counterclockwise direction (left) to remove it.
3. Hold the unit in place with one hand. Turn the bulb in a counter-clockwise direction (left) to loosen from the socket.
4. Take a new bulb and screw it into the unit using a clockwise motion. Wipe off fingerprints with a dry cloth.
5. Reassemble by reversing steps 1 & 2. Turn the unit back on and hold the UV-C control button for 3 seconds to reset the UV-C indicator light.
   • IMPORTANT: The UV-C bulb should be replaced every 10 months depending on the use

MAINTENANCE

• CLEANING
• Always unplug the appliance before you clean it.
• Never immerse the appliance in water or any other liquid
• Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any part of the appliance.

BODY OF THE APPLIANCE

Regularly clean the inside and outside of the body to prevent dust from collecting.

1. Wipe away dust with a soft dry cloth from the body of the appliance.
2. Clean the air inlet and the air outlet with a soft dry cloth.

PRE-FILTER SCREEN

• The pre-filter/charcoal layer collects larger dust and debris and should be cleaned monthly or more frequently depending on use. Remove and clean regularly with the brush attachment of your vacuum cleaner. This will remove the lint and dirt and help maintain the life of the filter. (See filter replacement to locate and clean or remove the filter).
• Replacement pre-filters are available by visiting our website at guardiantechnologies.com

TROUBLESHOOTING GUIDE

For more manuals by GermGuardian visit, ManualsLibraryy

GermGuardian AC3000 Airsafe+ Intelligent Air Purifier-FAQs