Pyle PDWR40W Indoor Outdoor Waterproof Speaker System
INSTALLATION
MOUNTING THE BRACKET
- Remove the bracket knobs and the bracket from the speaker
- Hold the bracket up to the mounting surface. “PYLE” can be mounted either horizontally or vertically. Hold the bracket so that the speaker wire fits through the large, circular wire hole in the bracket, and align the bracket to be square with the
surrounding (Use A level for accuracy) - Mark the locations of the three shaped screw holes, use all of the holes
- Drill pilot holes into the mounting surface
- Gently pull the speaker wire through the wire hole in the center of the mounting bracket, then the bracket so that the holes all line up.
- Use your hardware to attach the bracket to the mounting surface
FINAL ADJUSTMENTS
- After checking that the speaker is in-phase and works correctly, angle the speaker for the best sound
- Hand tighten the bracket knobs only, power tools may over-t ighten the knob, and strip the threads of the insert.
- Check that the entire installation is safe and secure..e
PDWR40W/PDWR40B
Excellent for use on Boa and its Marinas.Decks. Patios.Poolside.Outdoors.Etc. Completely Water Proof. Each PDWR40B Features:
- -5 1/4″ Aluminum Injection Cone Woofer
- -40 OZ.Magnet Structure
- -1″ High Compliance Myiar Tweeter
- -Capacitor Crossover Network
- -Bass Reflex Vent for added Bass Response
- Heavy-Duty ABS Construction
- Quick Connect/Disconnect Speaker Terminals
- Unique Spring-Loaded Mounting System
- Removable Rustproof Mesh Grilfs
- Power …………………. 200 Watts RMS/400 Watts Peak
- Frequency Response …………………. ..40-22K HZ
- Impedance………………………………………… 4 Ohms
- Dimensions .. 6.25″ (W)x9.25″ (H)xS.75″ (D)
Connecting your Speakers
Connecting the speakers to your amplifier or receiver.
- First, turn your amplifier off to avoid damage that may result from accidental
shorting of the speaker leads. - Correct phase polarity is critical for proper stereo imaging and bass performance.
The red(+) terminal on your amplifier or receiver must be connected to the red (+) terminal on your speaker, the same applies for the black (-) terminal. - Connect one loudspeaker at a time to ensure proper connection of the left and right
channels. Make sure all wires are firmly fastened. - If you notice a high level of bass or central image focus, double-check
connections for proper polarity.
FOR MORE MANUALS BY PYLE, VISIT MANUALSLIBRARYY
Pyle PDWR40W Indoor Outdoor Waterproof Speaker System
What do I need for an outdoor speaker system?
You’ll need:
An amplifier/receiver with the right power rating.
Outdoor-rated speaker wire (direct burial cable if running underground).
What’s the Bluetooth PIN for Pyle outdoor speakers?
The default PIN is “0000” (four zeros).
How do I protect outdoor speaker connections from moisture?
Apply petroleum jelly (Vaseline) to wire connections.
Avoid tape, as it can trap moisture.
How does a waterproof speaker work?
Uses sealed enclosures, silicone gaskets, and coatings to block water/dust.
Rated via IP (Ingress Protection) standards (e.g., IPX5 for water resistance).
Should outdoor speakers be covered?
Yes! Covers protect against:
Rain/snow (prevents water damage).
UV rays (avoids material fading).
What makes a good outdoor speaker?
Weatherproof durability (resists rain, heat, cold).
Clear, powerful sound (optimized for open spaces).
How do I charge my Pyle speaker?
Turn off the speaker.
Plug in the charger.
The indicator light turns green (or off) when fully charged.
Can I connect multiple Bluetooth speakers?
On Android 8.0+, enable Dual Audio in Bluetooth settings.
For more than two, use apps like AmpMe.
What wire should I use for outdoor speakers?
16AWG for runs up to 50ft.
12/14AWG for longer distances (100ft+).
Always use outdoor-rated (UV-resistant) cable.
How do I stop others from connecting to my speaker?
Set Bluetooth to “hidden” mode (not discoverable).
Disable pairing when not in use.