ANJANK AC-190 Wooden Digital Alarm Clock FM Radio
Features
- Wireless Charging
- FM Radio
- 9 Minutes Snooze
- 5-level of LED Display
- 12/24H Mode
- Battery Backup(Only Memory function)
- USB Charging Port
- Sleep Timer ( In FM mode)
- Headphone Jack Supported
Power Specifications
Power adaptor:
AC100-240V, 50-60Hz
DC, 9V-2A 18W, Class 2
Getting Started
Plug in the adaptor into a standard household outlet to get the clock working. Insert two AAA batteries(Not included) to preserve the TIME and ALARM settings in case of the power outage.
Note:
- Under the battery power, the display will go blank and the preset alarm will not go off, but the TIME and ALARM settings are saved.
- Once the battery is removed and with an interruption of power, the TIME and ALARM need to be reset when the power comes back.
Front view:
Top view:
Back view:
Bottom view:
12 / 24H Switch
Press the “12/24H ” button to change the time mode. In 12-hour mode, the “AM” will appear in the morning, and the “PM” will appear in the afternoon.
Setting The Time
- Press the “TIME SET” button to start the time settings, then press the up and down buttons to set the right hour.
- Press the “TIME SET” button to set the MINUTE, then press the up and down buttons to set the minute.
- Press the “TIME SET” button again to end the setup.
Setting The Alarm and Alarm Tone
Note: Please carefully check the 12H/24H. In 12-hour mode, the indication AM or PM will be shown on the screen. In 24-hour mode, there’s no indication of “AM” or “PM” on the screen.
- Press the “ALARM SET” button to start the alarm settings, then press the up and down buttons to the set alarm hour you want.
- Press the “ALARM SET” button to set MINUTE, then press up the down and buttons to set the alarm minutes you want.
- Press the “ALARM SET” button to set up the alarm ringtone. A number will be shown on the display and sound will be played accordingly to indicate the alarm ringtone (# 01 is beep, #02 is FM radio). Pressing the up or down buttons to select your preferred ring type.
- Press the “ALARM SET” button again to end the setup.
Alarm On / Alarm Off
Alarm will be turned on after you set the alarm time, press the “ ALARM ON /OFF ” button to turn off the alarm.
Using The Alarm And Snooze
- When the alarm is ringing, press the “SNOOZE” button to activate the snooze. It will ring again after 9 minutes.
- When the alarm is going off, you can silence the alarm by pressing any button except the “SNOOZE” button on the top. Alarm will be go off on the next day.
- The beep alarm(#01 alarm tone) will last sound 5 minutes; the FM radio alarm (#02 alarm tone)will sound for 1 hour.
Setting The Manual-scan Radio Station
- Press the “Radio” button to turn the radio mode on or off.
- When the radio is on, press the up and down buttons to manually select your favorite channel.
Setting The Auto-scan Radio Station
- When the radio is on, long press the “Radio” button, FM radio will scan and auto-store the scanned stations. Then press the up and down buttons to select your favorite channel.
- It can save up to 30 channels.
- Rotate the volume slider at the back of the clock to adjust the Radio Volume. Volume adjustment is only used for FM radio volume.
Setting The Radio Alarm
When the radio is on, you can select the channel you want, then long press the “SNOOZE / DIMMER” button until the letter “AL” blinks on the display, then this channel will be saved as the second alarm ringtone (02 alarm ringtone).
Sleeper Timer Setting
When the radio is on, press the “SLEEP” button to enter the sleeper timer setting. You can select the sleep time from 10 to 120 minutes. Default state is off.
Using The Wireless Charging Function
Place your phone on the center of the wireless charging pad, the phone will light up to indicate the phone is charging.
Note:
- Supported devices: Supports all enabled wireless charging devices or devices with receiver such as iPhone, Samsung, HUAWEI and other smartphones.
- Provides the fastest wireless charging speed for your Phone at 7. 5W.
- Output: 5W/7.5W/10W.
USB Charging Port
The clock comes with a USB port that is used to charge your other phones or digital devices.
Note:
- Wireless Charging and USB Charging functions can work at the same time;
- USB Charging function may not be supported for some phones and electronics;
- Output: 5V /1A.
Display Brightness Adjustment
Press the “SNOOZE ” button to adjust 5 levels of brightness of the display. (Full, High, Medium, Low, Dark to your preference.)
Headphone Jack Support
Use a 3.5mm headphone to listen to your favorite radio station without disturbing other people near you.
Email Support
If any questions about the clock, please contact our customer support team through customer01@kerchanstar.com. We will deal with your issue within 24 hours.
Warranty
ANJANK backs 45-day money back and the 18-month warranty for our product in our store.
Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For more Manuals by ANJANK, visit ManualsLibraryy
ANJANK AC-190 Wooden Digital Alarm Clock FM Radio-FAQs
What is the warranty for the ANJANK alarm clock?
ANJANK provides a 45-day money-back guarantee for any reason and an 18-month warranty for added peace of mind. If you have questions, feel free to contact their support team.
How do I set the time on my ANJANK alarm clock?
Press and hold the TIME SET button. Use the HOUR and MINUTE buttons to adjust the time. Release the TIME SET button once the correct time is displayed. (Note: PM times are indicated with a PM light.)
Why is my digital clock losing time?
Digital clocks can lose or gain time due to slight changes in the internal oscillator’s vibrations. These changes may be caused by temperature or air pressure fluctuations.
How long does the clock battery last?
Typically, clock batteries last up to 5 years, but it’s recommended to replace them annually for consistent performance.
How do I manually set a radio-controlled clock?
Insert the battery, select your time zone, then press and hold the flap above the battery slot. Keep holding until the correct time is reached, then release.
How do radio alarm clocks work?
Radio-controlled clocks use an antenna to receive a time signal and a circuit to decode it. They automatically adjust the time, so manual setting isn’t usually needed.
What is a radio-controlled or atomic clock?
A radio-controlled (or “atomic”) clock automatically syncs with the U.S. Atomic Clock in Colorado. It updates daily for accurate time and adjusts automatically for Daylight Saving Time, Leap Years, and Time Zone changes.
How do I turn off the alarm on the ANJANK clock?
Press either the AL1 or AL2 buttons repeatedly to cycle through the alarm options: BUZZER, RADIO, or OFF to disable the alarm.
How do I change the system clock on my device?
Go to Start > Settings > Time & Language > Date & Time. Turn on Set time automatically for automatic updates, or manually adjust the date and time settings as needed.