HOLEWOR B09QKPD1BX Biometric Gun Safe
Package contents
Product diagram
FOREWORD(Very Important)
Regarding the Unlock Method of the Factory Setting
- In the initial state, the battery is not installed in this safe. You need to use the equipped mechanical key to open this safe.
- The battery compartment is inside the safe. You need to remove the battery cover and install 4 AA batteries according to the following diagram (pay attention to the positive and negative poles of the batteries).
- Note: The initial password is 000000, and pressing any fingerprint in the initial state cannot unlock the lock.
- Do not put the key in the safe.
Unlock method
- Find the Setting button
This setting button is located inside the safe, as shown in the figure. All settings are based on this setting button, so you need to first find it.
- Find the Setting button
This setting button is located inside the safe, as shown in the figure. All settings are based on this setting button, so you need to first find it.
- Fingerprint entry
How to press the fingerprint correctly (As shown in the following figure) When registering or recognizing fingerprint, the center of the finger must be placed on the reader. Wipe off the dust, sweat, and water on the finger, keep the finger clean, and press the finger correctly. It is recommended to record more fingerprints so that your fingerprint recognition will be smoother. The same finger can be registered fingerprint multiple times. It can also register the fingerprints of multiple fingersCorrect placement of fingerprint for registration
Short press the setting button, then press the 2 key on the numeric keypad, continuously press your finger three times, the fingerprint green light flashes twice, and the buzzer rings a long time to indicate successful fingerprint entry. You can enter a total of 100 fingerprints, and the more fingerprints you enter, the smoother your fingerprint recognition will be.
- Delete all passwords
Short press the settings button, then press the 3 keys on the numeric keypad. The fingerprint green light flashes twice and the buzzer rings a long time to indicate that all passwords have been successfully deleted.
- Delete all fingerprints
Short press the setting button, then press the 4 key on the numeric keypad. The green light of the fingerprint flashes twice and the buzzer rings once, indicating that all fingerprints have been successfully deleted.
- Time Setting
Short press the setting button, then press the 5 key on the numeric keypad. At this point, the numerical value on the screen will start flashing to indicate waiting for you to input the current time (24-hour system).After completing the input, briefly press the setting button again, the fingerprint green light flashes twice, and the buzzer rings once to indicate successful time setting.
- Turn on and off the buzzer sound
Short press the settings button, then press the 6 key on the numeric keypad to turn on or off the buzzer sound.
- Restore factory settings
Press and hold the setting button for 5 seconds; the fingerprint green light flashes twice, and the buzzer rings once to indicate that the factory settings have been restored. At this time, all fingerprints and passwords are cleared, and the initial password of 000000 is re effective.
- Low battery alarm
When the battery indicator flashes only one bar on the display screen, it indicates that the battery level is low and needs to be replaced in a timely manner. Reminder: When the battery is low, fingerprints cannot be entered, but passwords can be entered.
- External Power Supply:
If the batteries become fully depleted and the mechanical keys are not available, the included USB-C cable can be connected to the port on the side of the unit to provide power to the unit for unlocking and other operations. An AC power adapter (not included) is required for this feature.
Note: Power supplied through the USB-C port will not charge the batteries. This feature is only used as temporary power for operation when the batteries are depleted. - Steel Cable Installation
Short press the setting button, then press the 2 key on the numeric keypad, continuously press your finger three times, the fingerprint green light flashes twice, and the buzzer rings a long time to indicate successful fingerprint entry. You can enter a total of 100 fingerprints, and the more fingerprints you enter, the smoother your fingerprint recognition will be.
Note: Power supplied through the USB-C port will not charge the batteries. This feature is only used as temporary 
Warranty and Customer Service
Thank you for purchasing the HOLEWOR Biometric Pistol Safe. This safe is made to ensure the greatest safety and satisfaction. Please fully read the contents of this manual and save it for future reference. If any assistance is needed, please contact us by e-mail at holeworus@outlook.com
One year warranty
The original purchaser is guaranteed for a period of one year from the date of purchase against defects in material or workmanship. If any or all of the product is damaged due to defects in materials or workmanship, we will, at our own discretion, repair or replace the product for the original purchaser. For warranty claims, please contact us by e-mail at holeworus@outlook.com with the original order number.
Warranty limitations
HOLEWOR is not responsible for any direct, indirect, incidental, or other losses, including property damage (loss of unit or items stored in the unit), data loss, lost income, or loss of profits.
For more manuals by Holewor, visit ManualsLibraryy