Hyper Tough HT19-401-003-15 Cordless Portable Water Sprayer
COMPONENT LIST
- Lock-off switch
- On/off switch lever
- Hose adapter
- Battery protection cover
- Power nozzle
- Extension lance
- Nozzle adapter
- Multi-spray nozzle
- Fixing nail
- Hose connector
- Hose filter
- Floater
- Hose
- Hose clip
- Carry bag
- Hose filter (See Fig. E2)
- Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
| Charger Voltage | 120V~60Hz | |
| Voltage | 20V Max.** | |
|
Battery capacity | ABP118T | 2.5Ah |
| ABP118T7 | 2.0Ah | |
| HT19-401-003-17 | 2.5Ah | |
|
Charger rating | HT19-401-003-14 | 120V~60Hz, 50W 20V , 2.0A |
| HT19-401-003-13 | 120V~60Hz, 75W 20V , 3.0A | |
| ACG318W1U | 120V~60Hz, 18W 20V , 0.7A | |
| Charging time | 3hrs | |
| Pressure | Max. 320psi | |
| Max water flow rate | 0.53GPM | |
| Weight (with lance) | 2.8 lbs | |
- The accessories of battery charger ( HT19-401-003-14 / HT19-401-003-13 ) and battery pack (ABP118T / HT19-401-003-17 ) illustrated or described are not included in HT19-401-003-15 delivery.
ACCESSORIES
| 20ft (6m) hose | 1 |
| Extension lance | 1 |
| Multi-Spray nozzle | 1 |
| Carry bag | 1 |
| Battery pack (ABP118T7) | 1 |
| Charger (ACG318W1U) | 1 |
OPERATING INSTRUCTIONS
Intended Use
- This tool is intended for cleaning and watering.
ASSEMBLY & OPERATION
| ACTION | FIGURE |
| BEFORE OPERATION | |
| Installing the battery pack NOTE: Before operation, make sure the battery is locked into position securely and the battery protection cover is fully closed. | See Fig. A1 |
| Removing the battery pack Open the battery protection cover and press and battery pack release button repeatedly to get out the battery. | See Fig. A2 |
| Charging the battery pack More details can be found in the section “For battery charger”. | See Fig. A3, A4, A5 |
| ASSEMBLY | |
| Attaching extension lance to the power nozzle NOTE: When attaching, align the two projections on the lance with the grooves of the power nozzle as shown in Fig. B. | See Fig. B |
| Attaching the multi-spray nozzle NOTE: When attaching, gently pulling the nozzle to make sure it is locked into position securely. | See Fig. C |
| Attaching the hose to the power nozzle NOTE: After the draw hose is attached, check the connection by gently pulling upon the draw hose. It should not be pulled off. | See Fig. D1, D2 |
| Attaching your own water hose (optional) 1. Attach the quick connect adapter 2. Attach your household garden hose with suitable connectors NOTE: Except for the draw hose supplied, you can also connect the power nozzle to your own water hose with suitable connectors. NOTE: Check whether the filter screen is missing before retightening the hose adapter. (Fig. E1, E2) When retightening the hose adapter, please tighten securely. Otherwise, it may not draw any water for proper operation. WARNING: It is not recommended to connect the draw hose to your garden hose or your home tap. |
See Fig. E1, E2, E3 |
| OPERATION | |
| Selecting the nozzle pattern NOTE: Choose a suitable nozzle pattern according to your work. Spray patterns 0o, 15o, 25o and 40o are applicable for cleaning, and the spray pattern with the symbol is best suitable for showering. WARNING: Do not shift the nozzle pattern when the tool is powered on due to potential water leakage. Make sure the nozzle pattern symbol |
See Fig. F1, F2 |
| Start NOTE: At the first use, you need to empty the air in hose, place the power nozzle below waist level (<5ft/1.5m), then attach the pressure cleaning lance and set it at high pressure. It does not start working until the water goes up along the hose and sprays out. This could take up to 30 seconds or more depending on the fresh water source. | See Fig. G |
| Watering NOTE: It is recommended to use the low pressure mode for watering. | See Fig. H |
| Cleaning WARNING: Do not connect the machine to water supplies that are dirty, rusty, muddy, or corrosive. (Including window cleaning liquids, plant foods, or fertilizers etc.) NOTE: Not recommended for use with salt water, immediately rinse with fresh water for proper maintenance. | See Fig. I, J |
aligns with the indicator mark on tool, otherwise the nozzle will leak and there will be no sufficient pressure.(1) For charger ACG318W1U
- CHARGING PROCEDURES (SEE FIG. A3)
- Connect the battery charger to the power supply and the indicator light should turn to green. Then, slide the charger base on the battery pack to make connections and the indicator light will turn red to show that the charging has started. It will remain red until the battery is fully charged. A discharged battery at normal ambient temperature will take approximately 1.5 hours to reach a full charge. When charging is completed, unplug the charger and remove the battery pack.
NOTE: green = power on,red = charging.
(2) For charger HT19-401-003-14
IMPORTANT NOTES FOR CHARGING BATTERY
- The battery in your new tool is not charged when it leaves the plant. Therefore it must be full charged before using the first time.
- CHARGING PROCEDURE (SEE FIG. A4)
- 1) Plug the charger into an appropriate outlet. The light will be green.
- 2) Slide the battery pack into the charger, the light will turn to red to indicate the charging process has started.
- 3) When charging is completed, the light will turn to green. The pack is now fully charged, unplug the charger and remove the battery pack.
- CHARGING INDICATOR
Light Status Red on 
Charging Green on 
Fully Charged
3) For charger HT19-401-003-13
CHARGING PROCEDURE (SEE FIG. A5)
- 1) Plug the charger into an appropriate outlet. The light will be green.
- 2) Slide the battery pack into the charger, the light will turn to red to indicate the charging process has started.
- 3) When charging is completed, the light will turn to green. The pack is now fully charged, unplug the charger and remove the battery pack
- CHARGING INDICATOR
Light ON/OFF flash Status Red on 
Charging Green o Fully Charged
TROUBLESHOOTING
| Symptom | Possible causes | Solution |
|
Machine turns on but it does not draw any water or there is not sufficient pressure. | Power nozzle is too high from the water source surface. | Lower the machine below 5ft/1.5m. |
| Hose filter is blocked. | Take out the hose filter and rinse the parts with clean water. (See Fig. K1, K2) | |
| The users garden hose is not well connected to the machine. | Check and reattach the garden hose tightly. (See Fig. E3) | |
| Hose adapter looses. | Tighten the hose adapter securely with a spanner. | |
| The filter screen is missing. (See Fig. E2) | Contact service agent to get a filter screen. | |
| Pump, hose, or other parts are frozen due to outside temperatures. | Wait for the pump, hose or other parts to thaw. | |
| Hose kinks. | Straighten out the hose. | |
| Additional air could be sucked into the machine. | Remove the pressure cleaning lance to eliminate the air or remove the multi-spray nozzle to drain all the water completely. Then reattach the pressure cleaning lance or the multi-spray nozzle. | |
|
Multi-spray nozzle leaks. | The nozzle pattern does not spray correctly. | Make sure the nozzle pattern symbol aligns with the indicator mark on tool. |
| Fixing nail of the multi-spray nozzle loosens. | Tighten it with a hex key. | |
| Outlet pressure increases suddenly. | Multi-spray nozzle is blocked. | Replace with a new multi-spray nozzle. |
| Machine drains out water after stopping. | There is water remaining in the lance and pump after stopping. | Drain all the water completely before storage. |
|
Machine does not start. | The battery pack is not attached well. | Reinstall the battery pack. |
| Battery pack is empty. | Replace with a new battery pack or recharge the battery pack. | |
| Defective battery. | Replace with a new battery pack. | |
| Machine pressure is not consistent. | Additional air could be sucked into the machine. | Check connection between the hose adapter and the draw hose. |
| It is at low pressure setting. | No action need. | |
| Battery pack is empty. | Replace with a new battery pack or recharge the battery pack. | |
| The multi-spray nozzle is blocked. The current protection is activated. | Remove the multi-spray nozzle and turn on the machine. If the machine works normally, replace with a new multi-spray nozzle. | |
| The inlet hose emerges from the water. | There is water remaining in the machine. | Drain all the water completely and then put the inlet hose in the water. |
For more manuals by Hyper Tough, visit ManualsLibraryy
How do I set up the Hyper Tough cordless water sprayer?
Ensure the battery is fully charged, attach the spray wand to the hose, and connect the hose to the water inlet. Secure all connections before powering on the unit.
How long does the battery last on a full charge?
The battery provides approximately 20–30 minutes of continuous use, depending on the selected spray pressure and intensity.
Can I use the water sprayer with soap or detergent?
Yes, the sprayer includes a soap bottle attachment for applying soap or detergent. Ensure the soap is suitable for use with portable water sprayers.
How do I clean the sprayer after use?
Detach the hose and spray wand, then flush the unit with clean water to remove any residue. Wipe down the exterior and let all components dry completely before storing.
What should I do if the sprayer doesn’t turn on?
Check that the battery is fully charged and properly installed. Ensure the power switch is turned on and inspect for any blockages in the spray wand or hose.
Can I use the sprayer with a water source other than a tap?
Yes, the sprayer can draw water from a bucket, tank, or similar container. Make sure the water is clean to prevent clogging.
How do I adjust the spray pressure?
The sprayer features adjustable settings on the spray wand or nozzle. Rotate the nozzle to switch between different spray patterns and pressures.
What safety precautions should I follow?
Always wear protective gear, avoid spraying electrical devices, and never point the sprayer at people or pets. Disconnect the battery before performing maintenance.
Is the Hyper Tough sprayer suitable for heavy-duty cleaning?
The sprayer is designed for light to medium cleaning tasks such as washing vehicles, patios, and outdoor furniture. It may not be suitable for heavy-duty industrial cleaning.
What is the warranty period for this water sprayer?
Warranty details vary by region. Refer to the product manual or contact Hyper Tough customer support for specific warranty information.