Indesit XWDE 1071681 Washer-Dryer User Manual

Indesit XWDE 1071681 Washer-Dryer

Installation

• This instruction manual should be kept in a safe place for future reference. If the washer-dryer is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarize himself/herself with its operation and features.
• Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.
3. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them again if the washer-dryer needs to be moved to another location.
   • Packaging materials should not be used as toys for children.

Levelling

1. Install the washer-dryer on a flat, sturdy floor, without resting it up against walls, furniture, cabinets, or anything else.
2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured about the worktop, must not exceed 2°.

Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise, and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow sufficient ventilation space underneath the washer-dryer.

Connecting the electricity and water supplies

Connecting the water inlet hose

1. Connect the supply pipe by screwing it to a cold water tap using a ¾ gas threaded connection (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear.
2. Connect the inlet hose to the washerdryer by screwing it onto the corresponding water inlet of the appliance, which is situated on the top right-hand side of the rear part of the appliance (see figure).
3. Make sure that the hose is not folded over or bent.
   • The water pressure at the tap must fall within the values indicated in the Technical details table (see next page).
   • If the inlet hose is not long enough, contact a specialised shop or an authorised technician.
   • Never use second-hand hoses.
   • Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor: The drain hose may be connected to an under-sink trap. Before connecting
the drain hose from the machine, ensure that any blanks or removable ends have been removed from the
spigot. If it is placed over the edge of a basin or sink, be sure the free end of the hose is not underwater.

• We advise against the use of hose extensions; in case of absolute need, the extension must have the
  same diameter as the original hose and must not exceed 150 cm in length. Ensure that if the drain
  hose is pushed into a standpipe, the end does not go down more than 15 cm (6 inches). If the hose is pushed down too far, this may cause the machine to self-siphon, i.e., continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make sure that:

• The socket is earthed and in compliance with the applicable law.
• The socket is able to sustain the appliance’s maximum power load indicated on the Technical Data Plate fixed on the machine;
• The supply voltage is included within the values indicated on the Technical Data Plate fixed on the machine.
• The socket is compatible with the washing machine’s plug. If this is not the case, replace the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug, which can be plugged into a 13 amp socket for immediate use. Before using the appliance, please read the instructions below.

WARNING – THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA-approved fuse to BS 1362 should always be used, and the fuse cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.

Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your nearest Service Depot.

Removing the plug:
If your appliance has a non-rewireable moulded plug and you wish to reroute the mains cable through partitions, units, etc., please ensure that either: The plug is replaced by a fused 13-ampere rewireable plug bearing the BSI mark of approval. or the mains cable is wired directly into a 13-amp cable outlet, controlled by a switch (in compliance with BS 5733), which is accessible without moving the appliance.

Disposing of the plug:
Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally inserted into a socket. Instructions for connecting the cable to an alternative plug: Important: the wires in the mains lead are coloured by the following code:

• Green & Yellow
  • Earth
• Blue
  • Neutral
• Brown
  • Live

As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

• Connect the Green & Yellow wire to the terminal marked E or coloured Green or Green & Yellow.
• Connect the Brown wire to the terminal marked L or coloured Red.
• Connect the Blue wire to the terminal marked N or coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt regarding the electrical supply to your machine, consult a qualified electrician before use.

How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the following code:

• BLUE
  • NEUTRAL (N)
• BROWN
  • LIVE (L)
• GREEN & YELLOW
  • EARTH (E)

Disposing of the appliance:
When disposing of the appliance, please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above.

• The washing machine should not be installed in an outdoor environment, not even where the area is sheltered, because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.
• When the washing machine is installed, the mains socket must be within easy reach.
• Do not use extensions or multiple sockets.
• The power supply cable must never be bent or dangerously compressed.
• The power supply cable must only be replaced by an authorised serviceman.

Warning! The company denies all liability if and when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle “Auto Clean” (see “Cleaning the washing machine”).

Care and maintenance

Cutting off the water and electricity supplies

• Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washer-dryer and help to prevent leaks.
• Unplug the washer-dryer when cleaning it and
• During all maintenance work.

Cleaning the washer-dryer

• The outer parts and rubber components of the appliance can be cleaned using a soft
  cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
• The washer-dryer has an “Auto Clean” programme for its internal parts that must be run with no load in the drum.

For maximum performance, you may want to use either the detergent (i.e. a quantity 10% of the quantity specified for lightly-soiled garments) or special additives to clean the washer-dryer. We recommend running a cleaning programme every 40 wash cycles. To start the programme, press buttons A and B simultaneously for 5 seconds (see figure). The programme will start automatically and will last approximately 70 minutes. To stop the cycle, press the START/PAUSE button.

Cleaning the detergent dispenser drawer

To remove the drawer, press lever (1) and pull the drawer outwards (2) (see figure). Wash it under running water; this procedure should be repeated frequently.

Caring for the door and drum of your appliance

• Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the protective pre-chamber at the base of the pump.

• Make sure the wash cycle has finished and unplug the appliance.

To access the pre-chamber:

1. Take off the cover panel on the front of the machine by first pressing it in the centre and then pushing downwards on both sides until you can remove it (see figures).
2. Unscrew the lid by rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

• Never use second-hand hoses.

Precautions and tips

• This appliance was designed for domestic use only.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Do not dry unwashed items in the tumble dryer.
  • Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
  • Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber-backed articles, and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.
  • Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
  • The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that they items will not be damaged.
    WARNING: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
• Do not touch the machine when barefoot or with damp hands or feet.
• Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull.
• Do not open the detergent dispenser drawer while the machine is in operation.
• Do not touch the drained water as it may reach extremely high temperatures.
• Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself.
• Always keep children well away from the appliance while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
• Before loading laundry into the washer-dryer, make sure the drum is empty.
• During the drying phase, the door tends to get quite hot.
• Do not use the appliance to dry clothes that have been washed with flammable solvents (e.g. trichlorethylene).

Description of the washer-dryer

• Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
• ON/OFF button: Press this briefly to switch the machine on or off. The START/PAUSE indicator light, which flashes slowly in a green colour, shows that the machine is switched on. To switch off the washer-dryer during the wash cycle, press and hold the button for approximately 3 seconds; if the button is pressed briefly or accidentally, the machine will not switch off. If the machine is switched off during a wash cycle, this wash cycle will be cancelled.
• PUSH&WASH+DRY button: (see “Wash cycles and options”).
• WASH CYCLE SELECTOR KNOB: used to set the desired wash cycle (see “Table of wash cycles”).
• OPTION buttons: press to select the available options. The indicator light corresponding to the selected option will remain lit.
• TEMPERATURE button: press to reduce or completely exclude the temperature; the value appears on the display.
• SPIN button: press to reduce or completely exclude the spin cycle; the value appears on the display.
• DELAYED START button: Press to set a delayed start for the selected wash cycle; the delay period appears on the display.
• DRYING button: press to decrease or exclude drying; the selected drying level or time will appear on the display (see “How to run a wash cycle or a drying cycle”).
• START/PAUSE button and indicator light: When the green indicator light flashes slowly, press the button to start a wash cycle. Once the cycle has begun, the indicator light will remain lit in a fixed manner. To pause the wash cycle, press the button again; the indicator light will flash in an amber colour. If thesymbol is not illuminated, the door may be opened. To start the wash cycle from the point at which it was interrupted, press the button again.
• Standby mode: This washer-dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. Press the ON-OFF button briefly and wait for the machine to start up again.
• Consumption in off-mode: 0,5 W
• Consumption in Left-on: 8 W

Troubleshooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list.

For more manuals by Indesit, visit ManualsLibraryy

Indesit XWDE 1071681 Washer-Dryer-FAQs