Nutribullet RX NB-301 Blender User Manual

Nutribullet RX NB-301 Blender

Important safeguards

ELECTRICAL SAFETY
When using any electrical appliance, basic safety precautions should always be observed.
Including the following:

• CAUTION! To avoid the risk of electric shock, never immerse the cord, plug, or motor base of the NutriBullet Rx in water.
• Do not use this product with any type of adaptor or voltage converter device.
• The use of attachments that are not recommended or sold by NutriBullet may cause fire, electric shock, or injury and void the warranty.
• Use of adapters and voltage converters is considered an unauthorized modification
  of the product and, as such,h will void the warranty. Use of this product in countries
  with different electrical specifications may damage the product.
• Depress the Power Button to OFF and unplug the NutriBullet Rx when it is not in use. Make sure the motor base is unplugged before assembling, disassembling, adding additional parts, or cleaning.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
  agent or similarly qualified persons to avoid a hazard.
• Do not pull, twist, or damage the power cord.

HEAT CAUTIONS

• During souperblast mode, the contents inside can reach up to about 70°C / 150°F through the friction of the rotating blade.
• Keep hands and other exposed skin away from the lid opening to prevent possible burns during souperblast mode.
• Do not remove the lid during the processing of the soup—ingredients will become hot and may splash out and cause injury.
• Do not touch the souperblast pitcher directly with your hands after the souperblast mode! The souperblast pitcher surface, blades, and coupling gear will be hot!
• Always use appropriate heat-resistant pads on the handle to hold the SouperBlast pitcher and to support the bottom of the container.
• Always attach the blade to the souperblast pitcher and hand-tighten or use the blade remover to tighten the blade to prevent leakage before adding ingredients into the
  pitcher.
• Never use the extractor blade to blend without liquid, as doing so may damage the blade or motor.
• Do not use the souperblast pitcher on the motor base without the black lid and clear vent top in place when running the nutribulletRx®.

CLEANING SAFEGUARDS

• After making a smoothie or souperblast, the blade must be cleaned immediately.
•  Always unplug the motor base and depress the power button before cleaning, assembling, or disassembling.
• Never submerge the motor base in water or place it in the dishwasher. Wipe off any debris inside the motor base immediately to keep it in good working order.
• Do not wash the blades in the dishwasher as elevated temperatures can damage gasket seals.
• Do not remove the rubber liner inside the motor base. To clean, unplug first, then wipe with a sponge moistened with warm water.
• The nutribulletRx®Rx®  cups can be washed in the dishwasher and should be washed on the top rack of the dishwasher using the normal (not sanitize) cycle.
• Blades are sharp! Use care when cleaning blades to avoid injury! Rinse blades immediately after each use to prevent debris from drying and sticking to blade
  components. If necessary, use the included brush to loosen any debris around blades, gaskets, and blade housing threads with care.
• Handwash only with mild dish soap and warm water (not hot).
• Dry immediately.
• For tough debris, fill the cup ½ full with room temperature (not hot), mild soapy water. Then, simply twist on the blade, pop it on the base, and give it a run for 30-45 seconds. Follow up with a thorough brushing..

STUBBORN CLEANUP

• If ingredients dry inside the nutribulletRx® cups or souperblast pitcher, make your cleanup a snap by filling the cup about 2/3 full with room temperature soapy water and screw on the extractor blade and if using the souperblast pitcher, put on lids. Place the cup assembly on the nutribulletRx® motor base for about 20-30 seconds. This will loosen the stuck ingredients, and with a light scrub and rinse in warm water, you’ll be all done.

What’s included?

How it works.

DO NOT RUN SOUPERBLAST MODE WITH ANY OF THE BLENDING CUPS. ONLY USE THE VENTED SOUPERBLAST PITCHER.

Extracting for smoothies.

1. Add ingredients into one of the cups.
2. Fill with liquid up to the MAX Line. Then, twist the extractor blade onto the cup and tighten by hand to make sure the vessel is sealed.
3. Plug the motor base into an electrical outlet. Press the power button, located at 90˚
   to the left side of the n. Button to turn the machine on. The power button light will glow BLUE, signifying power. Next, place the cup blade-side-down onto the motor base. This will activate the NutriBullet Rx® ’s SMART Technology function, causing the n. Button at the front of the unit to glow GREEN, and initiate the 1-minute extraction cycle.     
4. When the cycle has completed and the GREEN light has turned off, turn off the unit by depressing the power button, located 90˚ to the left side of the n.-Button.
   The BLUE light will stop glowing, signifying the power is off.

NOTE: You can remove the cup at any time during the blending cycle by simply lifting the cup off the motor base. If more extraction is required, lift the cup off the motor base, wait 15 seconds, then return it back onto the motor base to start another SMART Technology cycle. Do not repeat more than 3 consecutive cycles, resting 15 seconds between cycles. If you press the GREEN n.-Button for 2 seconds and the light turns
ORANGE, you have switched to souperblast mode. Simply lift the cup off the motor base
at any time to exit this mode or press the power button, located 90˚ to the left side of
the n.-Button. When the vessel is removed from the motor base, only the n.-Button light
will turn off. When the power off button is pressed, the BLUE light will turn off and the blade will stop spinning. Always press the power off button upon completion of processing.

Extracting for souperblasts.

1. Twist the extractor blade onto the SouperBlast pitcher.
2. Add ingredients to the SouperBlast pitcher and securely attach the vented, 2-piece.             
3. Plug the motor base into an electrical outlet. Press the power button located 90˚ to the left side of the n.-Button to turn the machine on. Next, place the pitcher blade-side-down onto the motor base. This will activate the NutriBullet Rx® ’s SMART Technology function, causing the n.-Button at the front of the unit to glow GREEN.           
4. Press the GREEN n.-Button down for 2 seconds until it glows ORANGE. This will
   indicate that souperblast mode has begun. The unit will run in souperblast mode
   for about 7 minutes before automatically turning off, causing the ingredients inside the souperblast pitcher to heat up to about 70 degrees Celsius/150 degrees Fahrenheit. The unit is programmed to slow down twice during the 7-minute cycle to allow ingredients to settle for improved processing. This is normal. Do not repeat souperblast mode for the same hot soup.

If more heat is required, place the contents in a microwave-safe container and continue heating to the desired temperature. To make a new soup, empty the old contents, add new
ingredients, and wait 1 full minute before returning the vessel to the motor base to start a new SMART Technology cycle. Do not repeat more than 2 cycles in the upperblast mod, resting 1 minute between cycles. After 2 consecutive cycles, allow the NutriBullet Rx®
motor base and souperblast accessories to cool off for 30- 60 minutes. Depress the power
button upon completion

Cleaning.

Stubborn cleanup

If ingredients dry inside the nutribullet Rx® cups or souperblast pitcher, make your cleanup a snap by filling the cup about 2/3 full with room temperature (not warm or hot) soapy water and screw on the Extractor Blade and if using the souperblast pitcher, put on lids. Place the cup assembly on the NutriBullet Rx® motor base for about 20-30 seconds. This will loosen the stuck ingredients, and with a light scrub and rinse in warm water
water, you’ll be all done.

CLEANUP THE  NUTRIBULLET RX® MOTOR BASE
For the most part, the motor base doesn’t get dirty, but if you neglect to twist the blade onto the cup tightly, liquids can leak out and get into the base and activator buttons.
HERE’S HOW TO CLEAN IT UP.
STEP 1: The most important thing is to depress the power button and UNPLUG the motor base before!

STEP 2: Use a damp rag to wipe down the inside and outside of the motor base.

• NEVER SUBMERGE THE MOTOR BASE IN WATER OR PLACE IT IN THE
  DISHWASHER.
• Never put your hands or utensils near the moving blade, and never use your hands or utensils to press the activator buttons down while the motor base is plugged i.n

WASHING THE NUTRIBULLET RX ®
Cleaning the NutriBullet Rx® is so easy… simply place any of the pieces (except for the motor base and blade holder) on the top shelf of the dishwasher or hand wash with warm, soapy water and rinse.

CLEANING SAFEGUARDS

• After making a smoothie or souperblast, the blade must be cleaned immediately
• Always unplug the motor base and depress the power button before cleaning, assembling, or disassembling
• Never submerge the motor base in water or place it in the dishwasher. Wipe off any
  debris inside the motor base immediately to keep it in good working order.
• Do not wash the blades in the dishwasher, er as elevated temperatures can damage
  gasket seals.
• The NutriBullet Rx® cups can be washed in the dishwasher and should be washed on the top rack of the dishwasher using the normal (not sanitize) cycle.
• The NutriBullet Rx® cups and blades should not be immersed in boiling water for
  Any reason that this will warp plastic and damage gaskets?
• Blades are sharp! Use care when cleaning blades to avoid injury! Rinse blades
  immediately after each use to prevent debris from drying and sticking to blade
  components. If necessary, use the included brush to loosen and remove debris around blades, gaskets, and blade housing threads with care.
• Hand-wash only with mild dish soap and warm water (not hot).
• Dry immediately.
• For tough debris, fill the cup ½ full with room temperature (not warm or hot), mild soapy water. Then, simply twist on the blade, pop it on the bae, and give it a run for 30-45 seconds. Follow up with a thorough brushing.
• When washing blades, do not attempt to remove the gasket ring. Simply hand wash the blades in warm, mild, soapy water. Attempted removal of the gasket may PERMANENTLY DAMAGE THE BLADE CONFIGURATION AND CAUSE LEAKAGE.

FOR MORE MANUALS BY NUTRIBULLET, VISIT MANUALSLIBRARYY

Nutribullet RX NB-301 Blender-FAQs