SHARP SPC1010ODX Accu-Set Digital Wall Clock
FEATURES
- LCD
- Wall mount
- UP / 12/24 button
- TIME SET button
- CAL. SET button
- Lithium battery compartment
- Battery compartment
- DOWN / °C/°F button
- Table stand
- TIME ZONE switch
- RESET button
- DST ON/OFF button
SETTING THE PROCEDURE FOR THE CLOCK
Before inserting the 2ì AAi batteries into the battery compartment
- Slide the Time Zone switch to the correct time zone.
- Press the DST button to turn on the DST function if your area observes DST.
- Once all the above is completed, insert 2 x AA/ LR6 batteries (preferably alkaline batteries) into the battery compartment, following the polarity as shown on the diagram inside the compartment.
- The clock will fast forward to the correct time.
Note: Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries, only batteries of the same or equivalent type as those recommended are to be used. Do not mix new and old batteries.
OPTIONAL MANUAL TIME SET FUNCTION
- Press and hold the TIME SET button, and the hour digit will start flashing.
- Press the UP or DOWN button to advance to the correct hour.
- Press the TIME SET button again, and the minute digit will start flashing.
- Press the UP or DOWN button to advance to the correct minute.
- Press the TIME SET button again to confirm the setting.
OPTIONAL MANUAL CALENDAR SET FUNCTION
- Press and hold the CAL. SET button, the year digit will start flashing.
- Press the UP or DOWN button to advance to the correct year.
- Press the CAL. SET the button again, the month digit will start flashing.
- Press the UP or DOWN button to advance to the correct month.
- Repeat the above steps for date and language, and press the CAL. SET the button again to confirm the setting.
TEMPERATURE DISPLAY
- The temperature displays the indoor temperature. At any time, we switch between Celsius and Fahrenheit by pressing/C/F button.
12/24 HOUR DISPLAY
- Press the 12/24 button to switch between 12-hour and 24-hour display modes.
DST FUNCTION
- If you live in an area that does observe DST, press the DST button to turn on the DST function. The clock will now adjust automatically each spring and fall to correct for the 1-hour time change.
- If you live in an area that does not observe DST, such as Arizona, Hawaii, or parts of Indiana, you do not need to make any settings.
REPLACING 3V LITHIUM BATTERY
The Accu-Set time memory is maintained by a lithium button cell battery, model CR2032. The expected life of this battery is about 3 years. Be sure that the two AA/LR6 batteries in the clock are fresh. This battery is located in the small battery compartment. Open the lithium battery compartment with a screwdriver and replace the CR2032 lithium battery observing the polarity. Then, close the compartment.
MAINTENANCE
- The batteries should be replaced if the display screen or alarm becomes dysfunctional or weak.
- Please use a soft cloth to clean the clock.
- Do not use any corrosive cleanser or chemical solutions on the clock.
- Do not expose to water or outdoors, this is for indoor use only.
RESET
- If the clock display does not work during setting, please check that batteries are in battery compartment completely nd correctly with battery polarity as shown on the diagram. If this doesnit work, use a slim but blunt object e.g. toothpick etc. to press RESET hole, then the clock will return to the initial mode.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the authority to operate the equipment.
FCC WARNINGS
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For Customer Service Please Call Toll Free at 1-(800)-221-0131 and ask for Customer Service. Monday-Friday 9:00 AM – 4:00 PM EST.
Please call for assistance before returning the clock to the store.
One-Year Limited Warranty
M.Z. Berger & Company warrants the original consumer purchaser of this product that it shall be free of defects in materials and workmanship for one year from the purchase date of this product. Defects caused by tampering, improper use, unauthorized modifications or repairs, water immersion, or abuse are not covered by this warranty. If a defect covered by this warranty occurs during the warranty period, wrap your clock carefully and send it to the following address:
MZ Berger Service Center 29-76 Northern Boulevard Long Island City, NY 11101
You must include a Proof of Purchase, either the original receipt or a photocopy, and a check or money order for USD 6.00 to cover the cost of handling. Also, include your return address inside the package. M.Z. Berger will repair or replace the clock and return it to you. M.Z. Berger will not be liable for any loss or damage, including incidental or consequential damages of any kind, from any breach of warranty, either expressed or implied, relating to the product. Since some states do not allow the exclusion or limitation of incidental or consequential damages, this limitation may not apply to you.
Printed in China
Model: SPC10100DX
For more manuals by SHARP, visit ManualsLibrary
SHARP SPC1010ODX Accu-Set Digital Wall Clock- FAQs
How do I set the time on my Sharp Accu-Set digital wall clock?
Slide the LOCK switch on the back of the clock to the TIME position. Then, press and hold the SET button on top of the clock for 2 seconds to start time setup.
How can I change the time or calendar on my Sharp wall clock?
Move the SETTING switch to either TIME SET or CALENDAR SET. Use the UP and DOWN buttons to adjust the values, and press ENTER to confirm your changes.
How do I reset my Sharper Image atomic clock?
If your clock isn’t showing temperature data, unplug the AC adapter, remove the batteries, and press any button 20 times to fully reset the device.
Does the Sharp atomic clock automatically set itself?
Yes, Sharp atomic clocks use a built-in receiver to sync with the official WWVB signal from the National Institute of Standards and Technology (NIST) in Fort Collins, Colorado.
What does the WAVE button do on an atomic clock?
The WAVE button forces the clock to receive the atomic signal manually. Hold it for 3+ seconds to start synchronization. The hands will reset and attempt to receive the signal.
How do I set the time zone on my Atomix clock?
Use the time zone slider on the back of the clock to select your region. To turn Daylight Saving Time (DST) on or off, hold the DST button for 3 seconds. You can also change the temperature display from °C to °F by holding the °C/°F button for 3 seconds.
How do I turn off the alarm on my Sharp clock?
If you see “Alarm 1” or a bell icon on the screen, it means the alarm is on. Press the Alarm 1 button (usually upper right) to deactivate it — the icon will disappear.
How do I silence the alarm on a Sharper Image clock?
Press any of the bottom buttons (S, M, ▲, ▼) when the alarm rings to stop it. If no action is taken, the alarm will turn off automatically after 1 minute. To snooze, press the front of the device.