2Boom BT268 Bluetooth Speaker
Power
- Please charge your Bluetooth speaker fully before its first use.
To charge the battery
- Using a Micro USB Charging Cable (included), insert the USB power cable into the micro USB port located on the back of the speaker. Connect the other end of the USB cord into a powered USB source such as a computer, laptop or USB AC adapter.
- When your Bluetooth speaker is charging, the indicator light will turn red. Once your Bluetooth speaker is fully charged, the red light will turn off.
Playing Music via Bluetooth
- Turn your Bluetooth speaker on by sliding the power switch located on the back of the speaker to ‘ON” position. The light will be on at the same time
- Make sure the Bluetooth function on your device is turned on.
- Search the speaker named,” 2BOOM-BT268″ Once you have selected the pair name, your device will pair with the device.
- Once your speaker is paired, a tone will be heard. Start playing music on your device.
- Make sure that you keep your device within a 33 feet range of your Bluetooth speaker.
- Adjust the volume of your device to a comfortable level. Turn off the unit when not in use.
Specification
- Speaker output: 3W*1
- Drive unit: 52mm
- Battery Capacity: 350mAh
- Frequency Response: 160Hz-18KHz
Caution
- This is not a toy. Please keep away from children.
- Please keep away from water / heat.
- Low power may cause poor connection even no working of Bluetooth.
- Do not overcharge the battery.
- Battery pack shall not be exposed to excessive heat such as sunshine, fire or the like.
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. - Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure requirement. The device can be used in portable exposure condition without RF striction.
For more manuals by 2Boom visit, ManualsLibraryy
2Boom BT268 Bluetooth Speaker-FAQs
How do I know when my 2BOOM speaker is fully charged?
The RED LED turns off when the speaker is fully charged.
How do you reset a 2BOOM speaker?
Switch off the speaker, then turn it back on to reset to factory settings.
How to set up a 2BOOM Bluetooth speaker?
Turn on the speaker, enable Bluetooth on your device, and search for “2BOOM-BT268”.
How do I check my speaker battery level?
Check the indicator lights on the speaker, which provide information about the battery level.
Can you overcharge a speaker battery?
Yes, overcharging can affect the battery’s performance and lifespan.
How do I turn off 2BOOM?
Press and hold the power button for 2-5 seconds.
Why is my 2BOOM speaker not charging?
Check the USB port, try turning the speaker on and off, and ensure the charging cable is secure.
How do you power a Bluetooth speaker?
Charge the speaker using a USB cable connected to a computer, laptop, or portable power station.
What is the Bluetooth code for speaker?
The default passkey is “0000”.
How do you charge a 2BOOM?
Connect the speaker to a USB cable and charge for about an hour.