Wali WL-M002 Rack and Stand User Manual

Wali WL-M002 Rack and Stand

UNPACKING INSTRUCTIONS

• Carefully open the carton, remove contents and lay out on the cardboard or other protective surface to avoid damage
• Check packages content against supplied parts list in the next page to assure that all components were recieved undamage. Do not use damaged or defective parts.
• Read all the instructions before attempting installation.

IMPORTANT SAFTEY INFORMATION

• Install and operate this device with care. Please read the instructions before installation and carefully follow all instuctions contained her in. use proper saftey equipments during installation.
• Please call a qualified installation contractor for help if you dont understand these directions or have any doubts about the saftey of installation.

Do not use this product for any purpose or in any configuration not expliity specified in this instuction. We hereby disclaim any and all liability for injury and damage arising from incorrect assembly, incorrect mounting or incorrect use of this product.

Supplied Parts List

CAUTION: This monitor desktop mount must be securely attached to the horizontal desk. If the mount is not properly installed it may fall, resulting in possible injury and/or damage.

Step 1 Install the Pole to the Desktop

Option A: Desk Clamp Install

1. Install the “C”-Clamp Brace(c) to the Pole (a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 1.
2. Install the “C”-Clamp(b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to three positions. Connect it using 2pcs M8x12 Bolts(g), and tighten using the Allen Key(o). Tighten the “C”-Clamp to the desktop using the plastic knob, see Figure 2.

Option B: Grommet Base Install

Existing Grommet Hole Installation

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.

1. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 3.
2. Position the Pole(a) on the mounting surface and secure using the Support Plate (j), M10 Washer(k), Spring Washer(l) and M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 4.

Self Drilled Grommet Hole Installation

1. Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8″ (10mm) diameter hole at the marked position through the mounting surface.
2. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 5.
3. Position the Pole(a) on the mounting surface and secure using the Support Plate (j), M10 Washer(k), Spring Washer(l) and M10 Bolt(i). Fasten the M10 Bolt using provided Wrench(p), see Figure 6.

Step 2 Install Arm to the Pole

Install Swivel Arm(d) to the Pole(a). Fasten the bolt with supplied Allen Key(o). Attach the Wire Clip(n1,n2) to the
Pole(a) and Swivel Arm(d).

Step 3 Attach the VESA Plate to the Monitor

• For Monitor with Flat Back
• For Monitor with Curved or Recessed Back

Step 4 Slide the Monitor onto the Head of Swivel Arm

• Slide the monitor onto the head of Swivel Arm(d) as shown in the above diagram.
• Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.

Step 5 Fix the Tilt Angle and Adjust the Level of Monitor

• Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle.
• If one monitor is lower, remove the Nut(h) and turn the bolt counter-clockwise with supplied Allen key(o) to raise the monitor. Install the Nut(h) after the adjustment.

Step 6 Make the Necessary Adjustments and Manage the Wires

• Use the supplied Allen Key(o) to make the necessary adjustments
• Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use.

For more manuals by Wali Electric, visit ManualsLibraryy