Ariston ARM7L 105-EX Washing Machine User Manual

Table of Contents

Ariston ARM7L 105-EX Washing Machine

Installation

Unpacking and levelling

Unpacking

Remove the washer-dryer from its packaging.
Make sure that the washer-dryer has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.
Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).
Close the holes using the plastic plugs provided.
Keep all the parts in a safe place: you will need them again i the washer-cryer needs to be moved to another location.

Packaging materials should not be used as toys for children.

Levelling

Install the washer-dryer on a flat, sturdy floor, without resting it up against walls, furniture, cabinets, or anything else.
If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front fest the angle of inclination, measured in relation to the work, must not exceed 2°.
Leveling the machine correctly will provide ft with stability, help to avoid vibrations and excessive noise, and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washer-dryer.

Connecting the electricity and water supplies

Connecting the water inlet hose

Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 ges threaded opening.
(see figure). Before performing the connection, allow the water to run freely until it is perfectly clear.
Connect the hoses to the washer-dryer by screwing them onto the corresponding water inlet of the appliance, which is situated on the top right-hand side of the rear part of the appliance.
Make sure that the hose is not folded over or bent.

The water pressure at the tap must fall within the values indicated in the Technical details table.
If the inlet hose is not long enough, contact a specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor: alternatively, rest on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end | of the hose should not be underwater.

We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity socket, make sure that:

The socket is earthed and complies with all applicable laws.
The socket is able to withstand the maximum power 102d of the appliance as indicated in the Technical data table.
The power supply voltage falls within the values indicated in the Technical data table (see opposite);
The socket is compatible with the plug of the washer-dryer. If this is not the case, replace the socket or the plug.

The washer-dryer must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms, and other weather conditions.

When the washer-dryer has been installed, the electricity socket must be within easy reach.

Do not use extension cords or multiple sockets.

The cable should not be bent or compressed

The power supply cable must only be replaced by authorised technicians.

Warning! The company shall not be held responsible in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry. Using the wash cycle 1.

Description of the washer-dryer and starting a wash cycle

Control panel

Detergent dispenser drawer: used to dispense detergents and washing additives (see Detergents and laundry).
ON/OFF button: switches the washer-dryer on and off.
WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold wash cycle (see Personalisation)
DRYING knob: used to set the desired drying programme (see Personalisation).
WASH CYCLE PROGRESS/DELAY TIMER indicator lights: used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress. If the Delay Timer function has been set, the time remaining in the wash cycle will be indicated (see next page).
DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press this button again.

Indicator lights

The indicator lights provide important information. This is what they can tell you.

Delayed start

If the DELAY TIMER function has been activated (see “Personalisation”), after the wash cycle has been started, the indicator light corresponding to the selected delay period will begin to flash:

As time passes, the remaining delay will be displayed, and the corresponding indicator light will flash:

Once the set delay has elapsed, the flashing indicator light will switch off and the selected wash cycle will begin.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.

Note: during the “Drain” phase, the indicator light corresponding to the “Spin” cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator light will illuminate.

If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash, and the function will not be activated:

If a function that is incompatible with another function selected previously is selected, only the most recent selection will remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off before you open the appliance door.

N.B. If the DELAY TIMER function is activated, the door cannot be opened; pause the machine by pressing the START/PAUSE button if you wish to open it.

If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see “Troubleshooting”)

Starting a wash cycle

Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off, and the START/PAUSE indicator light will pulse.
Load the laundry and close the door.
Set the WASH CYCLE knob to the desired programme.
Set the washing temperature (see Personalisation).
Set the drying cycle if necessary (see Personalisation).
Measure out the detergent and washing additives (see “Detergents and laundry”).
Select the desired functions.
Start the wash cycle by pressing the START/PAUSE button, and the corresponding indicator light will remain lit in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
At the end of the wash cycle, the END indicator light will switch on. The DOOR LOCKED indicator light will switch off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

Wash cycles

Table of wash cycles

For all Test Institutes:

Test wash cycle in compliance with regulation EN 50229: set wash cycle 6 with a temperature of 60°C.
Long wash cycle for cottons: set the wash cycle 1 with a temperature of 40°C.
Short wash cycle for cottons: set the wash cycle 2 with a temperature of 40°C.

Specials wash cycles

Sanitizing cycle (wash cycle 6)

A high-temperature hygienic wash cycle (over 60°C) requires the use of bleach. Pour the bleach, the detergent, and the additives into the relevant compartments (see paragraph entitled “Detergent dispenser drawer’)

Goodnight cycle (wash cycle 7)

This is a silent cycle that can be run at night, when the electricity prices are lower. The wash cycle is designed for cottons and synthetics. At the end of the cycle, the machine stops while there is still water in the drum; to spin and drain the laundry, press the START/PAUSE button; alternatively, the machine will perform the spin cycle and drain the water automatically after 8 hours.

Baby cycle (wash cycle 8)

This wash cycle can be used to remove the soiling typically caused by babies, while ensuring that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added 10 the detergent.

At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle, press the START/PAUSE button.

Mix 30 (wash cycle 4)

This wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 3 kg.

Mix 15 (wash cycle 5)

This wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash.

The washer-dryer will automatically prevent you from selecting a temperature that is higher than the maximum value set for each wash cycle.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results every time. To activate the functions:

Press the button corresponding to the desired function.
The function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the selected wash cycle.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

This option is enabled with all programmes.

Extra rinse

By selecting this function, the efficiency of the rinse is increased, and optimal detergent removal is guaranteed. It is particularly useful for sensitive skin.n

This function may not be used in conjunction with wash cycles 4, 5, 11, 12, 13, B, and C.

TF Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this function offers a high-performance wash.

This function may not be used in conjunction with wash cycles 4, 5, 6, 9, 10, 11, 12, 13, A, B, C.

1000-500

Selecting this function reduces the spin speed.

This function may not be used in conjunction with wash cycles 9, C, 11, 12, 13.

Care and maintenance

Cutting off the water and electricity supplies

Turn off the water tap after every wash cycle. This will wear on the hydraulic system inside the. washer-cryer and help to prevent leaks.
Unplug the washer-cryer when clearing it and during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser by raising it and pulling it out (see figure).

Wash it under running water; this operation should be repeated frequently.

Caring for the door and drum of your appliance

Always leave the porthole door ajar in order to prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump which doss not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber, which protects the pump, situated in its bottom part.

Make sure the wash cycle has finished and unplug the appliance.

To access the pre-chamber:

Using a screwdriver, remove the cover panel on the lower front part of the washer-dryer.
Unscrew the lid by rotating it anti-clockwise: a little water may trickle out. This is perfectly normal;
Clean the inside thoroughly.
Screw the lid back on.
Reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any cracks, they should be replaced immediately: during the wash cycles, water pressure is very strong, and a cracked hose could easily split open.

Never use second-hand hoses.

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make sure that the problem cannot be solved easily using the following list.

The washer-dryer does not switch on.

The appliance is not plugged into the socket fully or is not making contact.
There is no power in the house.

The wash cycle does not start.

The washer-dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Personalisation”).

The washer-dryer does not take in water (the indicator light for the first wash cycle stage flashes rapidly).

The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.

The washer-dryer continuously takes in and drains water.

The drain hose is not fitted at a height between 65 and 100 cm from the floor (see “Installation”).
The free end of the hose is underwater (see “Installation”).
The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, tum of the water tap off, switch the appliance off, and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washer-dryer to fill with water and rain continuously. Special anti-draining valves are available in shops and help to avoid this inconvenience.

The washer-dryer does not drain or spin.

The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.
The ANTI-CREASE function has been activated: To complete the wash cycle, press the START/PAUSE button (‘Personalisation’).
The drain hose is bent (see “installation”).
The drainage duct is clogged.

For more Manuals by Ariston, visit ManualsLibraryy

Blog Post