Closunt Astronaut Star Projector Kids Night Light
Attention
- The light source of stars and nebulae is strong, so eyes should not look directly at the light source.
- The brightness of the stars (i.e. laser brightness) is affected by the ambient temperature and time of use. When the ambient temperature is hot or the power-on time is longer, the brightness of the laser will decrease due to the heat of the light source. At this time, just turn off the power and let the laser emit the heat dissipation of the device (heat dissipation time usually takes more than 15 minutes), and then turn it on to restore the brightness.
- The head and body of the astronaut are connected together by magnets, and the direction of the head can be adjusted. Do not stretch the astronaut’s head and body forcefully, otherwise, the wires may break due to stretching.
Please install the base before using it. Please make sure that the astronauts’ feet are in full contact with the bottom of the base seat.
The projection direction can be adjusted by adjusting the rotation angle of the astronaut’s head.
Host Key Operation Instructions
Note: The product needs to be connected to the power cord for use.
Power switch:
Short press the power switch to turn on, and the stars and mixed color nebula are turned on by default after turning on.
Nebula Switch:
Short press the Nebula button to switch the color of the nebula, each time you press to switch a color, and so on; long press to turn off the Nebula function, and then short press to turn on the Nebula function again.
Star switch:
Short press the key to switch the respiratory rate of a star each time. Long press to turn off the star function. After turning it off, short press again to turn on the star function.
Timing indicator:
After pressing any timing button on the remote control, the timing indicator light will be on, and the indicator light will be off when the timing is turned off.
Remote Control Instructions
Switch:
Short press the switch to turn on, and Nebula and Stars are turned on by default after turning on; short press the button again after turning on to turn off.
Timing button:
The timing function is divided into two levels, namely 45-minute timing / 90-minute timing. Press the first time, the timing indicator lights up blue, and enters 45 minutes timing; Press the second time, the timing indicator will be red, and enter the 90-minute timing; Under the timing state, the timing indicator is on for a long time; Long press to cancel the timer, and the timer indicator will go out after canceling.
Nebula Brightness+:
There are 5 levels of Nebula brightness. The default brightness is the middle level. Each time you press it, the brightness will increase by one level.
Nebula color switching:
Each time you press the button, the nebula will switch to one color. After a cycle, it will return to the default color. Long press the button to close the nebula. After closing the nebula, short-press the button to reopen the nebula.
Nebula change speed-:
Nebula change speed is divided into five gears 0-1-2-3-4: gear 0 is static, gear 4 is the fastest-changing speed, and the default gear is Gear 2. Every time you press it, the speed of Nebula changes by one level until it reaches level 0.
Nebula change speed+:
The change speed of the nebula increases by one level each time you press it, until the third level.
Nebula Brightness-:
There are 5 levels of Nebula brightness. The default brightness is the middle level. Each time you press it, the brightness will decrease by one level.
Star switch:
Long press the button to turn off the star, and then short press the button to turn the star back on. Star Breathing Rate-: Star breathing rate is divided into four gears 0-1-2-3, 0 gear means that the stars are always on, gear 3 is the highest frequency, and the default gear is 2 gears, every time you press the star. The breathing rate is reduced by one gear until it reaches the 0 gear.
Star Breathing Rate+:
Each time you press the star, the breathing rate will increase by one level, up to level 3.
Star Brightness-:
The star brightness adjustment is only limited to the normally bright mode. In the breathing state, this button is invalid. There are three levels of brightness adjustment. The default brightness is the brightest when the star is turned on. Each time you press it, the brightness will be reduced by one level until the darkest level.
Star Brightness+:
The default brightness is the brightest. When the brightness is dimmed, press this button once to increase the brightness by one gear until the brightest gear.
- Material: ABS/PC/PVC/TPE
- Product Color: White Laser
- Wavelength: 532 nm
- LED Power: < 5W
- Control Mode: Remote control
- Remote Control Range: < 5meters(Best distance)
- Power Supply: 100 – 240V~50/60Hz 0.4A
- Work Input: 5V-=1A
- Product Size: 120*113*228mm
- Applicable Environment: Indoor Home (Better in a dark environment)
- Working Temperature: -10° ~45°Celsius
For more such BLOGs, visit ManualsLibraryy
Closunt Astronaut Star Projector Kids Night Light-FAQs
How do I turn on the Closunt star projector?
Plug in the projector using a 5V USB cable and a 5V/2A adapter (adapter not included). Then slide the ON/OFF switch to the middle position on the main body to power it on.
How do I charge the astronaut star projector?
The projector charges through the port on the astronaut’s backpack, not the base. Charging takes about 3 to 6 hours, and it should not be used while charging.
Can I leave the star projector on all night?
It’s not recommended to leave the projector on all night, as too much light can affect sleep quality. Use the timer function or turn it off/dim it after your child falls asleep.
How do I charge the star projector if I don’t have a wall adapter?
You can also charge it using a USB port on your computer or laptop, just connect the USB cable from the projector to the available port.
How do I reset the star projector?
To reset, press and hold the power switch for 6 seconds. This is useful if the Wi-Fi or app connection is not working.
How do LED lights recharge in projectors?
Most LED projectors are powered directly through USB or mains power, not rechargeable. If batteries are used, they may be replaceable or rechargeable, depending on the model.
How does the projector work for kids?
The projector uses LED lights and lenses to shine star patterns onto walls or ceilings. It creates a calming and fun night-time environment.
Is the star projector safe for kids?
Yes, it’s safe for children when used properly. Avoid direct eye exposure to the lights, and keep the device out of reach of very young kids.
How do projector lights actually work?
Projectors use a bright lamp or LED light source, which shines through filters and lenses to create colorful images on a wall or ceiling. The brightness (measured in lumens) affects how clearly the image appears.