Ninja BN701 Professional Plus Blender User Manual

Ninja BN701 Professional Plus Blender

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ CAREFULLY BEFORE USE

FOR HOUSEHOLD USE ONLY

WARNING

To reduce the risk of injury, fire, electrical shock, or property damage, basic safety precautions must always be followed, including the following numbered warnings and subsequent instructions. Please do not use the appliance for anything other than its intended use.

Please read all instructions prior to using the appliance and its accessories.
Carefully observe and follow all warnings and instructions. This unit contains electrical connections and moving parts that potentially present a risk to the user.
Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp, loose blades that can cause injury if mishandled.
Take inventory of all contents to ensure you have all parts needed to properly and safely operate your appliance.
Blades are loose and sharp. Handle carefully.
DO NOT blend hot liquids or carbonated liquids. Doing so may result in pressure buildup and steam exposure that can pose a risk of the user being burned.
This product is provided with a Stacked Blade Assembly. ALWAYS exercise care when handling the blade assembly. The blade assembly is sharp and is NOT locked in place in its container. The blade assembly is designed to be removable to facilitate cleaning and replacement if needed. ONLY grasp the blade assembly by the top of the shaft. Failure to use care when handling the blade assembly will result in a risk of laceration.
Turn the appliance OFF, then unplug the appliance from the outlet when not in use, before assembling or disassembling parts, and before cleaning. To unplug, grasp the plug by the body and pull from the outlet. NEVER unplug by grasping and pulling the flexible cord.
Before use, wash all parts that may contact with food. Follow the washing instructions covered in this instruction manual.
Before each use, inspect the blade assembly for damage. If a blade is bent or damage is suspected, contact SharkNinja to arrange for replacement.
DO NOT use this appliance outdoors. It is designed for indoor household use only.
This appliance has a polarized plug (one prong is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT modify the plug in any way.
DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or is dropped or damaged in any manner. This appliance has no user-serviceable parts. If damaged, contact SharkNinja for servicing.
This appliance has important markings on the plug blade. The entire supply cord is not suitable for replacement. If damaged, please contact SharkNinja for service.
Extension cords should NOT be used with this appliance.
To protect against the risk of electric shock, DO NOT submerge the appliance or allow the power cord to contact any form of liquid.
DO NOT allow the cord to hang over the edges of tables or counters. The cord may become snagged and pull the appliance off the work surface.
DO NOT allow the unit or the cord to contact hot surfaces, including stoves and other heating appliances.
ALWAYS use the appliance on a dry and level surface.
DO NOT allow children to operate this appliance or use it as a toy. Close supervision is necessary when any appliance is used near children.
This appliance is NOT intended to be used by people with reduced physical, sensory, or mental capabilities, or a lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
ONLY use attachments and accessories that are provided with the product or are recommended by SharkNinja. The use of attachments, including canning jars, not recommended or sold by SharkNinja, may cause fire, electric shock, or injury.
NEVER place the blade assembly on the motor base without first attaching attached to the container with the lid also in place.
Keep hands, hair, and clothing out of the container when loading and operating.
During the operation and handling of the appliance, avoid contact with moving parts.
DO NOT fill the container past the MAX FILL or MAX LIQUID lines.
DO NOT operate the appliance with an empty container.
DO NOT microwave the container or accessories provided with the appliance.
NEVER leave the appliance unattended while in use.
DO NOT process dry ingredients with the Stacked Blade Assembly.

PARTS

Pitcher Lid
72 oz. Total Crushing® Pitcher
Stacked Blade Assembly
Motor Base (attached power cord not shown) 64 oz. max liquid capacity.

NOTE: The top flap of your box shows the select accessories that are included with your model.

FEATURES

Use the Power button to turn the unit on or off.

AUTO-IQ® PROGRAMS

Intelligent preset programs combine unique blending and pausing patterns that do the work for you. Once a preset program is selected, it will start immediately and automatically stop when blending is complete. To stop blending before the end of the program, press the currently active button again.

AUTO-IQ PROGRAMS FOR THE TOTAL CRUSHING® PITCHER

SMOOTHIE

Make a batch of super-smooth, sippable drinks and shakes from fresh or frozen fruit, liquids, and ice.

ICE CRUSH

Turn ice, juices, and fruit into expertly blended frozen drinks.

ICE CREAM

Create delicious and scoopable frozen desserts like ice cream or sorbet.

NOTE: The Ice Cream program is not available on all models.

MANUAL PROGRAMS

LOW, MEDIUM, and HIGH

When selected, each of these speeds runs continuously for 60 seconds. Press the currently active button again to stop the program sooner. They do not work in conjunction with any Auto-iQ programs.

PULSE

Offers greater control of pulsing and blending. Operates only when PULSE is pressed. Use short presses for short pulses and long presses for long pulses.

BEFORE FIRST USE

IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.

NOTE: All attachments are BPA-free and dishwasher safe. It is recommended that the container, lid, and blade assembly be placed on the top rack of the dishwasher. Exercise care when handling the blade assembly.

Remove all packaging materials from the unit. Exercise care when unpacking the blade assembly, as the blades are sharp.
The Stacked Blade Assembly is NOT locked in place in the container. Handle the Stacked Blade Assembly by grasping the top of the shaft.
Wash the container, lid, and blade assembly in warm, soapy water using a dishwashing utensil with a handle to avoid direct contact with the blades. Exercise care when handling the blade assembly, as the blades are sharp.
Thoroughly rinse and air-dry all parts.
Wipe the control panel with a soft cloth. Allow it to dry completely before using.

ORDERING REPLACEMENT PARTS

To order additional parts and attachments, visit ninjaaccessories.com.

USING THE TOTAL CRUSHING® PITCHER

IMPORTANT:

Review all warnings at the beginning of this Owner’s Guide before proceeding.
As a safety feature, if the pitcher and lid are not properly installed, the motor will be disabled. If this happens, repeat step 5 on the following page. When the pitcher and lid are properly installed, the program button LEDs will illuminate, indicating the appliance is ready to use.

NOTE:

If the unit is plugged in and powered on, but the pitcher is not installed, the LEDs on the control panel will flash.
Auto-iQ® programs have pauses and changes in speed throughout the cycle.
DO NOT add ingredients before completing the installation of the Stacked Blade Assembly.
If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
The pitcher lid handle will not fold down unless it is attached to the pitcher.

Plug in the motor base and place it on a clean, dry, level surface such as a countertop or table.
Lower the Total Crushing Pitcher onto the motor base. The handle should be aligned slightly to the right, and the pitcher should be oriented so the LOCK symbols are visible on the motor base. Rotate the pitcher clockwise until it clicks into place.
Exercising care, grasp the Stacked Blade Assembly by the top of the shaft and place it onto the drive gear inside the pitcher. Note that the blade assembly will fit loosely onto the drive gear.
Add ingredients to the pitcher. DO NOT add ingredients past the MAX LIQUID line on the pitcher.
Place the lid on the pitcher, aligning the triangle symbol on the lid with the triangle symbol on the handle. Press down on the handle until it clicks into place. The triangle symbols MUST be aligned for the lid to lock and the unit to operate. Once the lid is locked in place, press the Power button to turn the unit on. The available program buttons will illuminate, and the unit will be ready for use.
If using an Auto-iQ® program, first select the program that best suits your recipe. The preset feature will automatically stop at the end of the program. To stop the unit at any time, press the currently active button again. If using a manual program, select your desired speed. Once the ingredients have reached your desired consistency, press the active button again, or wait for the unit to come to a complete stop after 60 seconds.
To remove the pitcher from the motor base, turn the pitcher counterclockwise and then lift up.
To pour out thinner mixtures, ensure the lid is locked in place, then open the pour spout cap. For thicker mixtures that cannot be emptied through the pour spout, remove the lid and Stacked Blade Assembly before pouring. To remove the lid, press the RELEASE button and lift the handle. To remove the blade assembly, carefully grasp it by the top of the shaft and pull straight up. The pitcher can then be emptied.
Turn the unit off by pressing the Power button. Unplug the unit when finished. Refer to the Care & Maintenance section for cleaning and storage instructions.

CARE & MAINTENANCE

CLEANING

Separate all parts. Wash the container in warm, soapy water with a soft cloth.

Hand-Washing

Wash the blade assembly in warm, soapy water using a dishwashing utensil with a handle to avoid direct contact with the blades. Exercise care when handling the blade assembly as the blades are sharp. Thoroughly rinse and air-dry all parts.

Dishwasher

All attachments are dishwasher safe. It is recommended that the lid, container, and blade assembly be placed on the top rack of the dishwasher ONLY. Ensure the blade assembly is removed from the container before placing it in the dishwasher. Exercise care when handling the blade assembly.

Motor Base

Turn off the unit and unplug the motor base before cleaning. Wipe the motor base with a clean, damp cloth. DO NOT use abrasive cloths, pads, or brushes to clean the base.

STORING

Wrap the power cord around the cord wrap on the back of the motor base. Store the unit upright and store the blade assembly inside or attached to the container with the lid locked in place.

DO NOT stack items on top of the container. Store any remaining attachments alongside the unit or in a cabinet where they will not be damaged or create a hazard.

RESETTING THE MOTOR

This unit features a unique safety system that prevents damage to the motor and drive system should you inadvertently overload it. If the unit is overloaded, the motor will be temporarily disabled. Should this occur, follow the reset procedure below.

Unplug the unit from the electrical outlet.
Allow the unit to cool for approximately 15 minutes.
Remove the container’s lid and blade assembly. Empty the container and ensure no ingredients are jamming the blade assembly.

IMPORTANT: Ensure that maximum capacities are not exceeded. This is the most typical cause of appliance overload.

If your unit needs servicing, please call Customer Service at 1-877-646-5288. So we may better assist you, please register your product online at registeryourninja.com and have the product on hand when you call.

TROUBLESHOOTING GUIDE

WARNING: To reduce the risk of shock and unintended operation, turn the power off and unplug the unit before troubleshooting.

The LEDs on the control panel are flashing.

If the unit is plugged in and powered on, but there is no container installed, the LEDs on the control panel will flash. Install a container, and the available program buttons will illuminate, indicating the unit is ready for use.

Unit doesn’t mix well; ingredients get stuck.

Using the Auto-iQ® programs is the easiest way to achieve great results. The pulses and pauses allow the ingredients to settle toward the blade assembly. If ingredients are routinely getting stuck, adding some liquid will usually help.

The unit moves on the counter while blending.

Make sure the surface and feet of the unit are clean and dry.

The unit doesn’t create snow from solid ice.

DO NOT use ice that has been sitting out or has started to melt. Use ice straight from the freezer.
Start with a few pulses and then use a continuous blending cycle. The pitcher lid handle will not fold down.
If not attached to the pitcher, the handle will not fold down. For storage, place the lid on the pitcher and press down on the handle until it clicks into place.

REGISTER YOUR PURCHASE

registeryourninja.com

For more Manuals by Ninja, visit ManualsLibraryy

Ninja BN701 Professional Plus Blender User Manual