Blog Post

ONN 100094748 Wireless Over-Ear Headphones-FEAT IMAGE

ONN 100094748 Wireless Over-Ear Headphones User Manual

onn logo

ONN 100094748 Wireless Over-Ear Headphones

ONN 100094748 Wireless Over-Ear Headphones-PROD IMAGE

Get to Know Your Wireless ANC Headphones

  1. Model: 100094748
  2. Speaker Diameter: 40mm
  3. Speaker Impedance: 320±15%
  4. Charging Cable: USB A to C 50cm
  5. Audio Cable: 120cm

What’s in the Box?

Check to make sure you have everything below.

ONN 100094748 Wireless Over-Ear Headphones-1

  1. Headphones x1
  2. 3.5mm audio cable x1
  3. Type-C charging cable x1
  4. Carry case x1
  5. Quick start guide x1

Let’s Get Started!

On/Off&Pairing

  • Power on the headphones and it will go to pairing mode automatically, search for the entry” onn. Over-Ear ANC”.
  • Multi-Point Connection: x2 Tap Power on button to enter pairing mode

ONN 100094748 Wireless Over-Ear Headphones-2

Enjoy Your Music

ONN 100094748 Wireless Over-Ear Headphones-3

Take a Phone Call

ONN 100094748 Wireless Over-Ear Headphones-4

Charge Your Headphones

ONN 100094748 Wireless Over-Ear Headphones-5

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, as specified in Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Need help?

We’re here for you every day from 7 a.m.-9 p.m. CST. Give us a call at 1-888-516-2630.

Produced for Walmart Inc.
Bentonville,AR 72716

For more manuals by ONN, visit ManualsLibraryy

ONN 100094748 Wireless Over-Ear Headphones- FAQs

How do I connect my ONN wireless headphones?

Turn on the headphones and put them in pairing mode. On your device, enable Bluetooth and select “ONN 100094748” from the list of available devices.

How do I put my headphones into pairing mode?

Press and hold the power button for a few seconds until the LED flashes blue and red. This indicates the headphones are ready to pair.

How do I know if my ONN headphones are fully charged?

The LED on the side shows the battery status: orange while charging and green when fully charged.

How long does it take to charge the headphones?

It takes about 2 hours to fully charge, giving up to 8 hours of playback time.

How do I reset my ONN headphones?

Locate the small reset button (usually inside the earcup or battery compartment). Press and hold it for 10–30 seconds using a pin or paperclip.

Why are my headphones flashing blue and red?

This indicates they are in pairing mode and ready to connect to a device.

How do I turn on my ONN headphones?

Press and hold the power button for 3 seconds until the LED lights up and you hear the “Power On” prompt.

Why is one side of my headphones not working?

Check the headphone connection, clean the jack if needed, ensure the device settings are correct, and reset the headphones if necessary.

How do I use my headphones properly?

Adjust the headband for comfort, place the earcups fully over your ears, and use the correct earbud orientation (L/R).

Leave a comment

Your email address will not be published. Required fields are marked *