T3 Cura Hair Dryer User Manual

T3 Cura Hair Dryer

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of burns, electrocution, fire, or injury to persons:

1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used on or near children or individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water. Return the appliance to a service center for examination and repair.
5. Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
6. Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
7. Never use while sleeping.
8. Never drop or insert any object into any opening.
9. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
10. Do not use an extension cord with this appliance.
11. Do not direct hot air toward your eyes or other heat-sensitive areas.
12. Attachments may be hot during use. Allow them to cool before handling.
13. Do not place the appliance, while it is operating, on any surface.
14. While using the appliance, keep hair away from the air inlet.
15. Do not operate with a voltage converter.

CHECK ALCI EVERY TIME YOU USE THIS HAIR DRYER

This hair dryer is equipped with an Appliance Leakage Circuit Interrupter (ALCI), a safety feature that renders it inoperable under some abnormal conditions, such as immersion in water. To make sure the ALCI is functioning properly and the exclusive water sensing system (ALCI) is working, perform the following test:

1. Plug in the hair dryer and press the test button on the plug.
2. The hair dryer will stop working. There will be an audible click, and the reset button will pop out.
3. To reset the ALCI with a Reset button: Unplug the unit. Then push the Reset button in and reinsert the plug into the outlet.
4. Be sure to repeat the test every time you use this hair dryer to confirm the ALCI is operational.
5. If the ALCI is not functioning properly, return the hair dryer to a service center.
6. If a water immersion occurs, bring this unit to a service center. Do not try to reset. Should the dryer go off and the Reset button pop out during use, this could indicate a malfunction in the dryer. Remove the plug from the outlet and allow the dryer to cool. Reset the ALCI. Reinsert the plug into the outlet. The dryer should function normally. If not, return it to a service center for examination and repair.

OPERATING INSTRUCTIONS

1. Press the Power Switch once to turn on the dryer. When turning the dryer on for the first time, it will start at the highest heat and speed setting. To turn off the dryer, press the Power Switch once again. NOTE: Each time you turn the dryer on, it will start on your last set temperature and speed.
2. To alternate between high and low speed settings, press the Speed Switch once.
3. To change the temperature, press the arrow on the Heat Switch to reach the desired heat setting.
4. To activate the cool shot, press and release the Lock-in Cool Shot Button once. To deactivate it, press the button again.

FILTER CLEANING INDICATOR

For optimal performance, this dryer features a filter cleaning indicator. When it is time for the filter to be cleaned, the lights will blink at a fast pace.

1. Twist the filter cap counterclockwise to release it from the air intake of the dryer body.
2. Brush or wipe away dust buildup on the interior screen and filter cap with a soft cloth or small brush.
3. To reset the filter cleaning indicator, hold the speed button for 3 seconds until the lights stop blinking.

HOW TO USE

1. Attach the Drying Concentrator to dry hair evenly with a wide volume of air.
2. Turn on the dryer and select your desired heat and speed settings. Aiming the Drying Concentrator in a downward direction, rough dry hair until it is 70-90% dry.
3. Remove the Drying Concentrator and attach the Styling Concentrator to style one section at a time with concentrated airflow.
4. Divide hair into 3-4 inch sections. Applying tension with a round bristle brush, brush through each section while following with the dryer. To smooth the ends, slip the brush underneath the curve and blow over the curve.
5. Finish by pressing the Lock-in Cool Shot Button and applying cool air to your hair to set your style.

MAINTENANCE INSTRUCTIONS

1. Make sure that the inlet and outlet grills are clear of dust and lint for proper operating performance.
2. Your hair dryer is virtually maintenance-free. No lubrication is needed.
3. Always remove the plug from the outlet and allow the dryer to cool before cleaning.
4. Twist the filter cap counterclockwise to release it from the air intake of the dryer body. Use a soft cloth or a small brush to remove dust and lint that may have accumulated on the metal mesh.
5. The hair dryer exterior may be wiped clean with a damp cloth.
6. CAUTION: Never allow the power supply cord to be pulled, twisted, or severely bent. Never wrap the cord tightly around the dryer. Damage will occur at the high flex point of entry into the hair dryer, causing it to rupture and short. Inspect the cord frequently for damage. Stop use immediately if damage is visible, if the unit stops, or if it operates intermittently.
7. If the cord or hair dryer is damaged or does not operate properly, return it to a service center for repair.
8. This hair dryer has no user-serviceable parts. Do not attempt to repair the appliance yourself.

T3 LIMITED WARRANTY TERMS & CONDITIONS

T3 Micro will repair or replace (at our option) T3 products for twenty-four (24) months from the date of purchase if they are defective in workmanship or materials. This limited warranty does not cover (1) damage due to misuse or abuse, such as incorrect voltage supply, dropping, or failure to follow enclosed instructions, or (2) tampering, such as repair or attempt to repair. To obtain service under this warranty, please visit t3micro.com/warrantyclaim to submit a warranty claim or call us at (866) 376-8880 to receive detailed instructions. You will be required to provide proof of purchase.

THIS LIMITED WARRANTY IS ONLY VALID IF THE PRODUCT IS PURCHASED FROM AN AUTHORIZED SELLER OF T3 GOODS AND IF THE ORIGINAL SERIAL NUMBER ON THE PRODUCT HAS NOT BEEN REMOVED OR OTHERWISE TAMPERED WITH. Any implied warranties, obligations, or liabilities, including but not limited to the implied warranty of merchantability and fitness for a particular purpose, shall be limited in duration to the 24-month duration of this written limited warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

IN NO EVENT SHALL T3 BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. Visit [www.t3micro.com/register](http://www.t3micro.com/register) to complete your warranty registration.

For More Manuals By T3 Micro, Visit ManualsLibraryy.

T3 Cura Hair Dryer-FAQs.