TRIBIT FlyBuds C2 BTH96 Earbuds 
Package Contents
- Earbuds(L/R)
- Charging Case
- USB-C Charging Cable
- User Manual
Product Parts
How to Wear the Earbuds
To Wear
Place the earbud in your ear canal and rotate it until comfortable.
To call
Aim the microphone at the mouth for a better call effect.
To Pick and Place
Power On/Power Off
- For the first time use, please tear off the insulation sticker.
- To Power On: Open the charging case.
- To Power Off: Close the charging case.
Bluetooth Connection Instructions
Connect the earbuds to a Bluetooth device
Open the charging case, and the earbuds will automatically enter the Bluetooth pairing mode; then the earbuds’ indicator lights will flash alternately red and white. Turn on the Bluetooth function in the Bluetooth device, refresh the Bluetooth device listing, then select the paired audio device named “Tribit FlyBuds C2” to connect. The indicator lights of the earbuds will go off after they connect successfully.
Connect the earbuds with other devices
Method 1
Please disconnect the earbuds from the currently connected Bluetooth device, and the earbuds will automatically enter Bluetooth pairing mode.
Method 2
Tap either earbud four 4 times. When the white indicator light goes on, touch and hold the earbud for 3 seconds. When the indicator lights of both earbuds flash in red at the same time, the earbuds will automatically enter Bluetooth pairing mode.
Touch Control Instructions
- Play / Pause: Tap either earbud twice
- Next Track: Triple-tap the right earbud
- Volume +: Touch and hold the right earbud (during a call or music playing)
- Volume -: Touch and hold the left earbud (during a call or music playing)
- Voice Assistant: Triple-tap the left earbud
- Answer a Call: Tap either earbud once
- End a Call: Tap either earbud twice
- Rejecting an incoming call: Touch and hold either earbud
- Power Off: Touch and hold either earbud for 10 seconds( without a call or music playing), and the red light will flash for 1s with the power-off prompt tone: Power OFF.
- Power On: Touch and hold the left and right earphones for 6s, and the white light will flash for 6s with the power-on prompt tone: Power ON
Charging Instructions
When the earbuds’ indicator lights flash slowly in red, please charge the earbuds in time.
To charge the earbuds
Put the earbuds into the charging case and close the case to start charging. The indicator lights on the far left and right of the charging box show the charging status of each earbud. During charging, the indicator lights will always be on and will go off after the earbuds are fully charged.
Charging time of the earbuds: about 90 minutes.
Open the top cover of the charging case, and it’ll display its battery level. When the battery runs out, the indicator light of the charging case will be off. Please charge the case in time.
To charge the charging case
Plug one end of the USB cable into a 5V power supply, and the other end into the charging port of the charging case for charging. The indicator lights will flash during the charging process, and the 4 indicator lights will stay on when the earbuds are fully charged.
Charging time of the charging case: about 90 minutes.
How To Reset The Earbuds
Step 1
Turn off the left and right earbuds. Touch and hold the touch area for 10 seconds (at the 6th second, the earbuds will turn on with the white indicator light flashing). Keep touching the earbuds at this moment until the white indicator light is always on.
Step 2
When the white indicator light is always on, double-tap the left and right earbuds within seconds to enter the reset state.
Step 3
When you have done the above 2 steps, if the earbuds are reset successfully, the white lights of the left and right earbuds will flash quickly.
Note: After resetting, if there is a Bluetooth device that has been connected to the earbuds, you need to delete the pairing record to allow the earbuds to be paired again.
Frequency band & Maximum transmission power
- Frequency band: 2402-2480MHz
- Maximum transmission power: -6 ~+4dBm
Warning
- Do not dismantle or modify the earbuds for any reason; otherwise, any malfunction of the earbuds is not covered by the warranty.
- Do not deliberately contact the earbuds with liquids, as this may damage the earbuds may be damaged and invalidate the warranty turns invalid.
- Do not place the earbuds in the environment where the temperature is too high or too low (above 45 °C or below -20 °C).
- This product includes a built-in lithium battery. It is forbidden to disassemble, bump, squeeze or throw the product into fire.
- Please keep the earbuds away from children to avoid accidental swallowing and other injuries.
Important Notes
- In a noisy environment, the voice from the earbuds will sound lower than the actual volume.
- Listening to music at high volume for a long time may cause permanent damage to your hearing.
- Please use the charging cable and power adapter or computer to charge the earbuds. When charging, only use the adapter that complies with the national/regional regulations and international and regional safety standards.
For more Manuals by TRIBIT, visit ManualsLibraryy
TRIBIT FlyBuds C2 BTH96 Earbuds-FAQs
How do I turn Tribit earbuds on or off using the charging case?
To power on, simply open the charging case lid. To turn them off, place the earbuds back in the case and close it.
How do I reset my Tribit FlyBuds C2 earbuds?
Reset by turning off both earbuds, then press and hold the touch buttons for 10 seconds until the lights flash. This clears previous Bluetooth connections.
How long does the Tribit FlyBuds series usually last on a single charge?
Tribit earbuds typically deliver up to 110 hours of total playtime with the charging case, depending on the model.
How do I check the battery level of my earbuds?
Open the charging case with the earbuds inside. The LED indicators on the case will show the current battery status.
What is the 60/60 rule for safe earbud use?
Listen at no more than 60% volume for no longer than 60 minutes at a time to prevent hearing damage.
Why is only one earbud working?
Try charging both earbuds, cleaning the mesh, reconnecting Bluetooth, or resetting the earbuds. Also ensure the audio balance on your phone isn’t shifted to one side.
Who manufactures Tribit earbuds?
Tribit is an audio brand known for affordable yet powerful earbuds and Bluetooth speakers.
How do I fully reset wireless earbuds if they won’t pair?
Turn both earbuds off, then hold the power or touch button for about 10 seconds to enter reset mode. Reconnect from your device’s Bluetooth menu.
How do I activate pairing mode?
Turn on Bluetooth on your phone. Then open the charging case or press/hold the earbud button until you hear “Pairing” or see blinking LEDs.