Adalov CPE365 Gigabit Wireless Bridge User Guide

Adalov CPE365 Gigabit Wireless Bridge

Get to Know About Your Wireless Bridge

Product Overview

Appearance

Port and Button Description

LED Explanation

Highlights

Using 5.8Ghz wireless technology;
Gigabit wireless bridge with 1000Mbps RJ45 LAN port;
Built-in 16 dBd high-gain directional WiFi antenna;
IEEE802.11ac IEEE802.11n, IEEE802.11a, IEEE802.3u;
Transmission distance up to 3km(direct line-of-sight);
Master bridge supports WiFi hotspot access;
Dialing pair, one key operation;
WDS networking mode;
Support point-to-point(PTP), point-to-multipoint mode (PTMP);
Dynamic MIMO power saving mode(DMPS) and APSD;
Support 24V POE power supply, easy to install and deploy;
Support WEB GUI access.

Package

Package Included:

2 x CPE365 Wireless Bridges,
2 x POE Adapters,
2 x Metal Cable Ties,
2 x Network Cables,
1 x User Manual.

Wireless Bridge Pairing & Installation

POE Power Supply

The CPE365 wireless bridge adopts a POE power supply, which is easy to install and manage while saving costs.

According to the requirements, prepare enough network cable (Recommended within 20 meters, must be Cat 5e network cable to connect the wireless bridge and the POE power supply. The POE port of the POE power supply is connected to the LAN port of the wireless bridge.
The LAN port of the POE power supply is connected to the PC, router, and switch.

Master Bridge & Slave Bridge Pairing

The bridges are pre-paired; just connect to the POE adapter, and it will auto pair in a few minutes; you can adjust the channel.

Set master/slave bridge:

Set master bridge–(switch “A-B” button to “A” position)

Set slave bridge– (switch “A-B” button to “B” position)

Please refer diagram below:

Short-press the reset button to change the channel from 0-9, A-F. The LED indicator will display the number to show what channel it is. Please keep the master and slave bridges in the same channel.
Wait for them to pair. When the signal light on the side turns on, it means the pairing is successful;

Master Bridge & Slave Bridge Installation

Install Wireless Bridge Diagram

Installation Steps:

Put the bridges’ front side face-to-face in the same direction, then use the ties to fix the CPE. (Note: The bracket is not included in the package).
Use a long network cable to connect the POE adapter and the bridge.
Master bridge connection:

Step 1: The LAN port of the POE Adapter connects to the router or the internet through an Ethernet cable.

Step 2: The POE port of the POE adapter connects to the POE/LAN port of the master wireless bridge with another Ethernet cable.

Slave Bridge (or slave bridges) Connection:

Step 1: The POE port of the POE adapter connects to the POE/LAN port of the slave bridge through an Ethernet cable

Step 2: The LAN port of the POE adapter connects to the LAN port of the computer or router with another Ethernet cable

Tips:

Before installation, please check whether the wireless bridge is paired well. Please refer to the master and slave pair setting page.
For installation, keep a clear line of sight between the 2 wireless bridges. There is no strong electricity, strong magnetism, or other signal interference between the two wireless bridges.
The signal transmission angle of the wireless bridge is 60 °. For point-to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60° signal range of the main bridge. The antenna polarization direction is horizontal 60°/ vertical 30°.

Point-to-Point Diagram

Point to Multipoint Diagram(Up to 8 slave bridges)

Note: There is only one Master bridge, and others all Slave bridges.

Note:

The slave bridges must be in front of the master bridge.
The master bridge and slave bridges must be face-to-face.
The maximum angle between the master bridge and slave bridges should not exceed 60 degrees.

Application

Point to Point for Network Extend Diagram:

Multiple Network Equipment Expansion Diagram:Point to Multi-Point Connection Diagram:

Multiple Clients Connection Diagram:

Repeater Mode Connection Diagram:

Computer Access

Modify the Computer’s IP

Refer to the figure left to connect the CPE to the computer through a POE adapter and an Ethernet cable.

Note: You can enable the device without advanced settings

Modify your computer’s IP address, make your computer’s IP address a bridge’s IP address be on the same network segment(LAN), so that you can access them.

Click the network icon in the lower right corner of the computer, then click “Network & Internet settings”
Select Ethernet and click “Change Adapter Options”
Find the network connection you are using, right-click it, and select “Properties”
Double-click the “Internet Protocol version 4(TCP/IPv4)” go to IP configure interface
Configure your computer IP address as 192.168.255.x (x is a figure 0-200).

Note: The Pc’s IP can not be the same as the bridge.

Log in via browser

Double-click the “Internet Protocol version 4(TCP/IPv4)” go to IP configure interface

Open the browser and enter the IP address of the wireless bridge to access. For example, enter “192.168.255.101″ in the browser address column, and you can access your bridge control panel.

A login screen will appear; by default, the Username and Password of the wireless bridge are all “admin”.

Note: “admin” is not the password of the WiFi SSID; it is just the password for WEB access

Advanced settings

How to Change Configuration

Set Master bridge

Turn off the Digital tube by “Digit-on/off”.

(Note: The digital tube mode must be turned off, then the settings can be saved.)

Then short-press the reset button, the digital tube won’t change the channel.

Hide SSID or Change SSID name and password:

In the wireless settings, you can turn on/off “Hide SSID”, modify the SSID name, and the WiFi password

Note: Please remember the new SSID name and WiFi password. Because the pair two bridges will need them.

Change the IP for the bridge: (I changed it to 116.30.231.100)

Set Slave bridge:

Open a browser and enter the slave bridge’s IP to access it.

Turn off the “Digit on/off”.

(Note: The digital tube mode must be turned off then the settings can be saved.)

Change the IP for the slave bridge. (I changed it to 116.30.231.200)

How to pair bridges in non-Digit tube mode

(After you change the IP of two bridges, then you want to access the bridge, please modify your computer’s IP; the IP must be in the same LAN as the bridge.)

Change your computer’s IP to 116.30.231.xxx (IP couldn’t be the same as two bridges)

Open a browser to access the slave bridge.

Click “Wireless 5GHz”-“Bridge” and choose the “AP-Client (AP is disabled)”. Then enter the STA SSID and Shared key (which is the new master bridge’s SSID and password) and click “Apply” to pair two bridges.

When the signal indicator lights up, it means pairing is successful.

After setting up the bridge, reset your computer’s IP.

After-Sales Service

Tips:

The installation of this device requires network knowledge. If you can not install it, please contact us or ask a professional for help. If the product you receive is damaged or if it is missing any accessories, please contact us for an exchange or a resend.
The wireless transmission maximum speed(wireless bridge A to B unit) is 900Mbps, the LAN network transmission maximum speed (POE adapter to wireless bridge connection) is 433Mbps, and the LAN port is 100/1000Mbps standard.

Tech Service email: [email protected]

For more Manuals by Adalov, visit ManualsLibraryy

Adalov CPE365 Gigabit Wireless Bridge User Guide