Soundcore Life P3i Hybrid Earbuds
Charging
- Fully dry off the earbuds and the USB port before charging.
- Use a certified USB-C charging cable and charger to prevent any damage.
- Fully charge both the earbuds and the charging case before the first use.
- Place the earbuds in the charging case and close it.
- Connect the charging case to the power supply by using a USB-C charging cable. The LED indicator on the charging case indicates the charging status.
Wearing
- Choose the EarTips that fit your ears best.
- Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.
- Your earbuds come with 3 pairs of EarTips, among which the Medium-sized are pre-installed.
Powering On/Off
- Open the charging case, and the earbuds will automatically power on.
- To power off, place the earbuds into the charging case and close it.
- The earbuds will automatically power off after 10 minutes if no device is connected.
- To manually power on, press and hold the multi-function button on both earbuds for 3 seconds.
Bluetooth Pairing
- Open the charging case, and the earbuds will automatically enter Bluetooth pairing mode.
- The LED indicator on the charging case will flash white.
- Select “Soundcore Life P3i” on your device’s Bluetooth list to connect.
- When successfully connected, the LED indicator on the charging case will turn off.
- Pairing with another device: Place the earbuds in the charging case and leave the case open. To enter pairing mode, press and hold the button on the case for 3 seconds until the LED indicator on the charging case flashes white.
- Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range.
- Mono mode: When Bluetooth is connected, you can use either one of the earbuds only by placing the other one into the charging case.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
- When you are on a call, place either one of the earbuds into the charging case, and the microphone in the other earbud will be activated.
Controls
Mono Mode
Reset
- You might need to reset the earbuds if you experience any connectivity problems or function issues.
- Place the earbuds into the charging case and keep the case open.
- Press and hold the button on the case for 10 seconds until the LED indicator on the charging case flashes red 3 times. This confirms that the reset was successful and your earbuds can be connected normally.
Specifications
Specifications are subject to change without notice.
For More Manuals By Soundcore, Visit ManualsLibraryy.
Soundcore Life P3i Hybrid Earbuds-FAQs
Q1. How do I set up and pair the Soundcore Life P3i earbuds for the first time?
Open the charging case. The earbuds will automatically enter pairing mode with the LED indicator flashing white. On your device, select “Soundcore Life P3i” from the Bluetooth list to connect. When paired, the LED turns off.
Q2. How do I manually put the earbuds into pairing mode?
Press and hold the button on the charging case for 3 seconds until the LEDs flash white in sequence. The earbuds will then be ready to pair with a new device.
Q3. Will my earbuds reconnect automatically after setup?
Yes. Each time you power them on, they will automatically reconnect to the last paired device if it is within Bluetooth range.
Q4. How do I wear the Soundcore Life P3i correctly?
Insert each earbud into your ears and gently twist for a snug fit. Make sure the microphone openings are facing outward.
Q5. How do I turn the earbuds on or off without the charging case?
To power on: Press and hold the earbud’s button for 2 seconds.
To power off: Press and hold either earbud’s button for 2 seconds.
Q6. How do I activate or switch noise control modes?
Press the “NC” button to cycle between:
Noise Cancelling (default)
Transparency Mode
Normal Mode
You can also customize noise control levels in the Soundcore app.
Q7. How do I charge the Soundcore Life P3i earbuds?
Place the earbuds into the charging case and close the lid. Connect the case to power using a USB-C cable. The LED indicators will show charging progress.
Q8. How do I know when the earbuds are fully charged?
31–70%: Left LED steady white, middle LED flashing, right LED off.
71–99%: Left & middle steady white, right LED flashing.
100%: All three LEDs steady white for 1 minute, then turn off.
Q9. Can I charge the Soundcore Life P3i wirelessly?
No. Only the Soundcore Life P3 supports wireless charging, not the P3i.
Q10. How do I reset my Soundcore Life P3i earbuds?
Press and hold the charging case button for 10 seconds until all three LEDs flash white three times, then continue flashing in sequence. This confirms a successful reset.