Tribit BTS 11 AquaEase Portable Speaker
Package Contents
Product Illustration
Tips: Support micro SD card up to 32 GB, support file system format FAT32.
How to Charge the Speaker
Connect the other end of the charging cable to a charging adapter and connect the charging cable to the USB-C charging port on the Bluetooth speaker.
Note:
During charging, the indicator light is always on in red.
When the speaker is fully charged, the red indicator light goes off.
When using in a wet or watery environment, please plug the silicone plug tightly to avoid water in the charging port.
Button Control
On/Off
Note: If the Tribit AquaEase Speaker is unable to be powered off due to unknown reasons, you can forcibly turn it off by pressing and holding the power button for 8 seconds, and then the speaker will restart automatically.
Bluetooth Connection
Tribit AquaEase
- Automatically reconnects to the last paired device.
- Connects 2 Bluetooth devices at the same time.
- Memories 8 Bluetooth devices.
Note: When 2 devices are connected to the Tribit AquaEase speaker, device A and device B cannot play simultaneously—only one speaker at a time.
Multifunctional Button (MFB)
Volume
Time setting
Ambient Light
Stereo Mode
- Make sure speaker A and speaker B are both turned on.
- Press and hold the Bluetooth button on speaker A for 5 seconds to enter the stereo pairing mode. ( Speaker A is the primary speaker.)
- Press and hold the Bluetooth button on speaker B for a second to enter the stereo pairing mode. (Note: If this speaker is already in pairing mode, there is no need to perform this operation)
- When you hear the prompt, “Stereo Mode”, the stereo pairing is successful.
When entering the Stereo Mode, the primary speaker reads, “left Channel” and the secondary speaker reads, “Right Channel”.
Note: Stereo mode is only available when there are 2 Tribit AquaEase speakers. And make sure the firmware of both speakers has been upgraded to the latest version through the APP.
Reset
If a malfunction occurs, you can try to reset the speaker ( press and hold the volume + button and volume – button at the same time for 5 seconds ) to remedy theissue. Oncee reset, all the old data has been wiped, and you need to pair the speaker to your Bluetooth device anew.
Specifications
- Bluetooth Version: V5.3
- Bluetooth Protocol: A2DP, AVRCP, HFP, HSP
- Output Power: 5W
- Frequency Response: 100~16KHz
- Frequency Band: 2402-2480MHz
- Maximum Transmission Power: ≤6dBm
- Battery: 3.7V, 2200mAh, 8.14Wh
- Charging Time: 3 hours @ DC 5V/1A
- Waterproof Rating: IPX7
- Size: 109.6 * 109.6 * 48.2mm
- Weight: 260g
Customer Service
- A12-month Warranty
- For more services and information, please email [email protected].
Safety Precautions
- Do not place the speaker in a place where it is easy to fall.
- IPX7 is tested under strictly controlled laboratory conditions. Water resistance may diminish over time under daily use. To prevent damage to the product from liquids, do not immerse the product in water.
- Do not disassemble, repair,r orrodify this product by yourself.
- Keep the speaker away from extreme temperatures.
- Do not use the speaker in an outdoor thunderstorm environment.
- Do not use any corrosive cleaners or other chemical solutions to clean the speaker.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions : : (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Caution
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
For more manuals by Tribit, visit ManualsLibraryy
Tribit BTS 11 AquaEase Portable Speaker- FAQs
How do I put my Tribit speaker in pairing mode?
Press and hold the Bluetooth button on the speaker until the LED flashes blue, indicating it’s ready to pair.
How can I pair two Tribit speakers together?
Turn on both speakers. Press and hold the Bluetooth and Volume buttons on the first speaker until you hear a voice prompt. Repeat on the second speaker. After a few seconds, you’ll hear “Party Mode,” confirming they’re connected.
How do I reset my Tribit Bluetooth speaker?
Turn off the speaker, then press and hold both the power and Bluetooth buttons for 5–10 seconds until the speaker restarts.
Can I factory reset a Tribit speaker?
Yes. Use the same steps as a reset: power off, then hold the power and Bluetooth buttons together for 5–10 seconds. This restores default settings.
How do I know when my Tribit speaker is fully charged?
While charging, the LED shows reddish-purple. When fully charged, it turns blue and stays on.
How long does it take to fully charge a Tribit speaker?
Charging typically takes 3–4 hours, depending on the power source and battery level.
How long does the Tribit speaker battery last?
Up to 30 hours at 50% volume with lights and XBass off. Battery life varies with volume and usage.
Why is my Bluetooth speaker not pairing?
Ensure both devices are in pairing mode, within range, and no other device is interfering. Restart the speaker or your phone if needed.
Can I play my speaker while charging?
Yes, Tribit speakers can be used while charging, but battery lifespan may slightly decrease over long-term use.
Should I leave my Bluetooth speaker plugged in all the time?
It’s safe occasionally, but keeping it plugged in constantly may gradually reduce battery capacity over years.